Leatherman quality control.
-
The shop where i buy my multitools in the #1 webshop in holland.
I dont think they will sell you old leathermans.
They are also certified leatherman import/retailer.I think that keeping the cost low is the reason why this flaw are in the tools.
-
Ex Swisstool x!
I've beat the living daylights out of LM tools for decades. I broke the plier head on a TTi Charge and a couple of ST flat drivers while using them to pry something, but all above and beyond the call of duty.
You've definitely had some bad luck there though, so good luck with the Sx and I'll keep an eye on the swiss section for the results :)
Sent from my iPad using Tapatalk HD
-
After reading your story, I was thinking the whole time, you need to try a swisstool or swisstool spirit, but you have one on order so you should be happy! I had too much rust issues with leathermans too so I gave up actually using them. I collect them still, but for tools I use its either the swisstool or swisstool spirit x. The full size swisstools are heavy duty beasts of pliers so if you break those you must be very strong!
As for manufacture the main body of the LM and most of the tools are made in USA. Only of 420 grade steel though which is why they rust easier than Victorinox. The plier heads are made in Mexico last I heard, and I believe the files are made there as well. The sheaths are made in china. Many people have commented on reduced quality over the years. Ive noticed it on the smaller tools alot like the ps4. The p4 was much more well constructed.
Looking forward to your thoughts on the swisstool!
-
The stories on the declining nature of Leatherman's quality control are anecdotal, but numerous enough to give one pause.
Were they made better back in the old days? All I can say is that I have a original Supertool that has been used and abused for 20 years and it's still working. There was a time where it was accidentally left outside overnight in the damp grass. I found it the next day and brought it inside, and promptly tossed the wet tool in a drawer without cleaning it. When I checked on it some time later, it hadn't rusted.
-
@Syph007 said:
After reading your story, I was thinking the whole time, you need to try a swisstool or swisstool spirit, but you have one on order so you should be happy! I had too much rust issues with leathermans too so I gave up actually using them. I collect them still, but for tools I use its either the swisstool or swisstool spirit x. The full size swisstools are heavy duty beasts of pliers so if you break those you must be very strong!As for manufacture the main body of the LM and most of the tools are made in USA. Only of 420 grade steel though which is why they rust easier than Victorinox. The plier heads are made in Mexico last I heard, and I believe the files are made there as well. The sheaths are made in china. Many people have commented on reduced quality over the years. Ive noticed it on the smaller tools alot like the ps4. The p4 was much more well constructed.
Looking forward to your thoughts on the swisstool!
I stil like leathermans.
But i don't want to EDC them anymore.
I like the way they have replaceable wire cutters and some other smart inventions.
But i also think that the replaceable cutters on the rebar, super tool 300 and new surge are giving um some strength.
because the've had to machine a place to fit the cutters.
But the breaking point is mostly near the joint and not in the cutter area.
If you over torque the screws you can create a fragile spot because the wholes in the plier jaws are one of the thinnest points in the plier.But i don't see a lot of broken rebar or super tool pliers.
i've used my swisstool for one day now and i like the blunt nose type more because its much stronger and i never really the thin part of the pliers on leatherman.
I use it mostly for cutting electrical wire, bending small things (not good for MT's) and torqueing bolts.
Leatherman has an excellent 25 year warranty but i never had a feeling that my leatherman will last for 25 years. (outside the part that i sometimes miss use my MT)
If i did not fasten the security screws over time i would lose them within a year.
not after 25 years.with the swisstool i have the feeling that it will last 25 years as long as i don't break anything.
-
@shamus said:
The stories on the declining nature of Leatherman's quality control are anecdotal, but numerous enough to give one pause.Were they made better back in the old days? All I can say is that I have a original Supertool that has been used and abused for 20 years and it's still working. There was a time where it was accidentally left outside overnight in the damp grass. I found it the next day and brought it inside, and promptly tossed the wet tool in a drawer without cleaning it. When I checked on it some time later, it hadn't rusted.
I don't know if they were made better but I like the old designs better. I am talking about the minitool and I freaking love it! A full set of pliers that fit in to the fifth pocket.

And yes I know it is off topic but I just had to do it. :D
-
@shamus said:
The stories on the declining nature of Leatherman's quality control are anecdotal, but numerous enough to give one pause.
Were they made better back in the old days? All I can say is that I have a original Supertool that has been used and abused for 20 years and it's still working. There was a time where it was accidentally left outside overnight in the damp grass. I found it the next day and brought it inside, and promptly tossed the wet tool in a drawer without cleaning it. When I checked on it some time later, it hadn't rusted.
I don't know if they were made better but I like the old designs better. I am talking about the minitool and I freaking love it! A full set of pliers that fit in to the fifth pocket.

And yes I know it is off topic but I just had to do it. :D
You're excused. :D And I agree.

-
Greetings OP,
I've been carrying a Skeletool for a little over three years now, and I haven't had nary a problem with my plier jaws.You say you keep breaking them when bending things. Are you twisting the plier head while bending? The Skeletool's jaws are rather narrow so that the tool fits comfortably in a pocket, so they're not really made to be twisted. When bending something, you should grab it end-on and move the tool as if you are turning a bolt, rather than grabbing the work perpendicular and twisting along the long axis of the tool. Remember that this is a thin bit of stainless steel, and it will give before a hardened steel bolt.
-
@av8r1 said:
Greetings OP,
I've been carrying a Skeletool for a little over three years now, and I haven't had nary a problem with my plier jaws.You say you keep breaking them when bending things. Are you twisting the plier head while bending? The Skeletool's jaws are rather narrow so that the tool fits comfortably in a pocket, so they're not really made to be twisted. When bending something, you should grab it end-on and move the tool as if you are turning a bolt, rather than grabbing the work perpendicular and twisting along the long axis of the tool. Remember that this is a thin bit of stainless steel, and it will give before a hardened steel bolt.
The breaking of the pliers where my fault.
Indeed the skeletool pliers are rather thin.
If you carry a skeletool you should teach your self not to twist the plier head.
In my case it was a a regular wood screw. put the screw in the cut out for bolts and twisted the screw.
But it still snapped even though it was close to the joint.
Conclusion: skeletool pliers are thin an not made for bending things. (never recommend bending things with MT)That is also the reason why i switched to rebar.
If i need a set of pliers i want the to be capable of doing some serieus stuff. -
Although the fit and finish on my Leatherman tools has never been as good as anything from Victorinox, durability has never been an issue for me. I owned an original Leatherman PST and after that got stolen purchased a Wave. Although I generally prefer Victorinox to Leatherman and would definitely like to get a Swisstool Spirit X someday, I would not fault Leatherman's quality. You must have had an incredible run of bad luck with your tools.
-
I wouldn't recommend bending with the hard wire cutter notch on any Leatherman pliers, as it's made to shear rather than to bend. That's a good way of damaging the tool in a way that the warranty wont' cover. When bending, I recommend using the needle nose section, and using a bolt-turning motion like I discussed rather than a twisting motion.
Wood screws (and in fact most threaded fasteners) are made of heat treated steel that is much harder than the cast stainless steel these tools are made of. Something like the rebar with their carbide cutters might be up to cutting hardened steel, but be aware of the force you're putting into the tool.
I've done some pretty heavy stuff with my Skeletool, but when bending stuff with a twisting motion I usually use the Wingman or Wave and their wider jaws. For really heavy jobs, I break out the box brake I built.
-
I've broke a leatherman, but I was abusing it. They're are good, but that's not the same as invincible.
-
I recently purhased a brand new TTI from a store here in South Africa. I have found that both main blades are gritty and difficult to open, I tried a bit of oil, but does not help. I do not want to return it to Leatherman RSA, as they replace units with refurb units. These sometimes have scratches and marks on them. I can see that there is only one copper washer between the frame and the blade, and not one on the handle side. Would it improve it by adding one on that side?<br />
<br />
I also have a Charge Al and Alx, and do not have this issue, blades open smooth, but i see there are washers on both sides of the main blade.<br />
<br />
Greetings from South Africa.Sent from my iPad using Tapatalk HD
-
I've said plenty of times before, I have had more than my fair share of quality issues with Leatherman, and actually came to believe for a while that any "B Grade" goods in the factory were destined for overseas sale rather than rejected or rectified. These days I just think they're bloody sloppy ::) The first two tools I bought of theirs were unquestionably defective (not just design issues), and I have had others since then, and heard of plenty more.
I DO NOT associate the brand name with a high quality reliable product!
I have several Leatherman tools that I own, like and use. These tend to be older models (from back when they cared about quality), or ones where I have done some modification. If I was to look for a new multitool for someone today the first brands I would consider are Victorinox and Gerber.
Victorinox does occasionally let the odd lemon out of the factory, but these are rare. Gerber are more hit and miss with their QA, probably on a par with Leatherman in my opinion, but their tools are often better priced, and generally offer better value for money in my opinion. As for SOG, my current perspective is that the odds of them getting something right, is about on a par with the odds of Victorinox getting something wrong.
-
@hugos said:
I recently purhased a brand new TTI from a store here in South Africa. I have found that both main blades are gritty and difficult to open, I tried a bit of oil, but does not help. I do not want to return it to Leatherman RSA, as they replace units with refurb units. These sometimes have scratches and marks on them. I can see that there is only one copper washer between the frame and the blade, and not one on the handle side. Would it improve it by adding one on that side?<br />
<br />
I also have a Charge Al and Alx, and do not have this issue, blades open smooth, but i see there are washers on both sides of the main blade.<br />
<br />
Greetings from South Africa.Sent from my iPad using Tapatalk HD
Can you not write and ask for a new replacement as it is a new product. Surely a phone call or email could do the job.
Re the Charge TTi, the ones I have worked with don't come with washers between the tools and handle slabs.
If you have the tools, it isn't difficult to dismantle everything. A clean and maybe a quick polish and it should work well. -
@50ft-trad said:
I've said plenty of times before, I have had more than my fair share of quality issues with Leatherman, and actually came to believe for a while that any "B Grade" goods in the factory were destined for overseas sale rather than rejected or rectified. These days I just think they're bloody sloppy ::) The first two tools I bought of theirs were unquestionably defective (not just design issues), and I have had others since then, and heard of plenty more.I DO NOT associate the brand name with a high quality reliable product!
I have several Leatherman tools that I own, like and use. These tend to be older models (from back when they cared about quality), or ones where I have done some modification. If I was to look for a new multitool for someone today the first brands I would consider are Victorinox and Gerber.
Victorinox does occasionally let the odd lemon out of the factory, but these are rare. Gerber are more hit and miss with their QA, probably on a par with Leatherman in my opinion, but their tools are often better priced, and generally offer better value for money in my opinion. As for SOG, my current perspective is that the odds of them getting something right, is about on a par with the odds of Victorinox getting something wrong.
That assessment seems to be spot on.
Sent from my iPhone using Tapatalk
-
I have three Leathermans.
They are all perfect.
I am happy.
:) -
I have one Leatherman.
It broke.
I am not happy.:(


Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
