Bit adapter madness
-
I found this adapter on a cheap tool. Outdoor Edge Trek Tool and thanks to Corrugated thread on SOG parts I put it on the SOG PowerLock and it fits fine. It takes up 5 implements so I don't see much of an advantage to having it. It looks cool though and if you want to use full size hex bits it will work for you.
.jpg)
.jpg)
-
@prime77 said:
Yes the adapter you are asking about is made by Gerber....If you do switch out the Suspensions skinny phillips driver for the older one you will have to go with the adapter that J-Sews posted because the newer on won't fit over the thicker driver. Hope this helps :)Thanks a lot, prime77. That does help.
This adapter looks to be a decent solution to immediately extend the functionality of my Suspension.
Eventually, if I am able to find a used Gerber tool with a bigger Phillips and file that will fit the Suspension, I do want to mod it.
However, this adapter would still work after the mod because my Suspension would still have the smaller Phillips.
So far, I haven't been able to find a source for these adapters.
The Gerber website is extraordinarily unhelpful at providing useful info on products. No decent pics, info on weights, dimensions, and no listings of exactly what accesories are available for the various products.
Is there anywhere that you know of to buy the correct bit adapter kit that will fit the Suspension?
Thanks again for your help.
.
-
I don't know of anywhere that just sells the bit adapter but I'll keep a look out for one.
-
This thread finally had the inevitable effect on me; I broke down and bought one of those Leatherman adapters. It came today, but.....
It didn't come with one of these fancy clamshell carrying cases like Prime has here:
Instead mine has a big dorky leather sheath, and a even dorkier plastic carrying contraption inside.

I like the adapter, but no way am I going to lug it around in a sheath that is bigger than my multitool sheath. :(
-
I thought that sheath actually looked pretty cool... :-[ :-[ :-[
But now I don't think I want to offer you a trade for it! :P
Def
-
Bob, that is the different style adapter from the one I have. I was wondering when being used with the SideClip does it fit into that cutout in the SideClips handles.
-
Mine is the Leatherman (Standard) Bit Adapter. It only fits the older PST, PST II, Mini-Tool, SideClip, etc. The paperwork that came with it is dated 1997, so apparently it is old stock. As ridiculous as this huge sheath and carrier are, Leatherman must have went back to the drawing board and came up with the plastic clamshell carrier at a later date.
Yes, the protruding tang fits exactly into the cutout in a SideClip's handle. I'm not sure what the purpose of the protruding tang is though?

-
Thanks Bob, it's strange that I find this stuff so interesting ::)
-
-
I agree. Man is known as the Tool Using Animal. What good is a tool using animal without a tool? Darwin would have slapped those other people for fouling up evolution.
Def
-
Thanks guys, It's good to know that I'm not alone.
-
You aren't alone... I'd say right about now there are probably about 410 souls in agreement with you!
Def
-
@prime77 said:
Yes the adapter you are asking about is made by Gerber. The one I have came with the Diesel model I have....Hope this helps :)prime77, can you tell if this http://www.cheaperthandirt.com/72915-5499-1278.html adapter fits the Diesel and Suspension?
The description says "fits all Gerber multi-plier" but that could well be in error.
Thanks again for your help.
.
-
I'm sorry that is the adapter that Jsews talked about that fits the older Gerbers not the Diesel and Suspension.
-
Yes, I agree. Ringzero, the one you linked to has a square hole in the base, made to fit the 400 and 600 series Gerber tools. It won't fit properly onto the new "flattened" phillips drivers like the Suspension has.
-
@prime77 said:
I'm sorry that is the adapter that Jsews talked about that fits the older Gerbers not the Diesel and Suspension.Thanks prime77, that's exactly what I feared might be the case.
Can't understand why Gerber doesn't make the bit adapters more available for Diesel and Suspension (and whatever other models that particular adapter would fit.)
I'm certain that some percentage of people who own a Diesel or Suspension would want to purchase a bit adapter kit to extend the capabilities of their multi.
If they knew it was available.
If they could find a source actually offering it for sale.
Seems to me that Gerber is missing out on additional sales for no good reason.
.
-
@prime77 said:
Bit adapters seem to be the norm with any new multitool that comes out. I think it's a good idea. Anything thats expands the usefulness of the tool works for me. Some work better than others. Here are a sampling of the ones I have. Do you guys know of any others.prime77, Nice thread! It's a very nice overview but you're missing one of my favorites. The Kershaw A100TA magnetic adapter has a unique design. The adapter is held by the locking pliers in either a 180 deg (shown), 90 deg, or 45 deg angle.

-
I had read about that adapter a while back but never saw any pictures of it. Thanks :) It looks to be truly an original.
-
I had the Kershaw tool a long time (before I discovered this place), but purchased one of the bit adapters after coming here, just for completeness sake. Has anyone tried to use it? Seems a bit awkward to me like it could slip out and/or be scratched up pretty good in the process. A unique design, for sure.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login