poor, poor, PST
-
Hi Mat,
I have thought about drilling out one side of the rivets and putting in "stock" PST pivot screws. I have a nearly mint Japan PST with hollow rivets that has a broken awl. So I have thought about making new rivets but that seems like a lot of work that could easily end with a tool that will not open.
I have opened up many a PST so if it would have been knurled fasteners I would have opened it up without a second thought.
I think the stake marks are a really neat opportunity to get lube into the plier pivot.
If the rust gets loosened up and turns to crud the ultrasonic cleaner will get it off the tool. Maybe a couple of cycles between the dip and ultrasonic?
I will take it out of the dip tomorrow for inspection.
Bruce
-
Looking forward to see how this goes..
Good thread Bruce.. :) -
Yeah, I hadn't caught that it was a riveted one. I'm honestly not familiar with the Japanese variant, and guess I'd jsut assumed all PSTs were knurled nut construction. Still happy to see how it goes and wish you the best of luck in its recovery. :D
-
Good thread title Bruce. :D Looking forward to seeing how this comes out. As you can't take the pivots apart I guess the best I could think of would be to attack them with a toothbrush.
-
Ok, a quick update. I went outside this morning and took a look at the tool. I should have tried to take a picture but I didn't. The tools are on a table on our deck and if you walk between the house and garage you pass the jars of dip. I shake the jars occasionally when I walk past just to agitate the tools. When I saw the Japan PST this morning it looked like it was covered with dirt, all the junk floating in the dip settled and a bunch was on top of the tool. So I got it out and wiped it off for a few pictures. Also, I noticed that the tool is soaking in Kroil Oil which is a really good penetrating oil. Expensive and smells like fish but it really works.
This side looks much better now:

The word that was written (Robinson) in blue permanent marker was on this side, unfortunately someone ground this side before they wrote on the tool:

Opposite side 1:

Opposite side 2:

The markings on the blade tang are somewhat visible now:

Sorry about the white balance, I did not set it for the lower light this morning and the tool is already back in the dip so....
Gareth, It was very much appreciated that you came up with the thread title. I was trying to figure out what to use when I read you message.
So much sooner than I thought the tool might be ready for the ultrasonic cleaner!
Bruce
-
wow, that's looking much better already! Shame about the poor grinding job but perhaps you might be able to polish it up some?
-
Great thread. Makes me want to resuscitate a PST too.
-
Looking much better!
-
-
Since the PST did so well overnight in the dip I decided to put a little more time into it. Plus, I am not leaving on a business trip this week so no leaving for the airport today.
I am very lucky that I have a Scotchbrite wheel exactly the same as what they use at Leatherman. I saw one sitting on a bench when we went on the tour at Leatherman and asked the guy running the grinder what grit it was. So I bought one and the adapters then I needed to find a good used 8" bench grinder to power the wheel. So it did a great job of cleaning up the one handle. I have always been disturbed by people cleaning up a Leatherman tool with a longitudinal stroke, the factory used a up and down stroke that looks very different that left to right. The blade on this PST and the grinding on the handle were both left to right. It looked like someone used medium sandpaper on the blade, so I touched it up a little on the Scotchbrite wheel and attached the handle that was ground.
Here is the tool sitting in my ultrasonic cleaner before I put in water:

I put in the water, detergent and vinegar (my cleaning mix) and the plier pivot looked like it was smoking:

That is dirt particles being driven out of the plier pivot, I was lucky I still had the camera in my pocket because it did not last for more than a minute. Here is a closer shot of the pivot:

It looks like just a dirty spot starting at about 3 o'clock on the pivot but it is stuff rising from the ultrasonic. There is a little still coming up from 9 o'clock but it just about ended by the time I got the picture taken.
So it looks like I have some play time today on tools.
Bruce
-
I hope it sees better days soon!
Sent from Ash forum mobile
-
Looking really good
I love it when a neglected tool gets a new life. -
Looking good Bruce
Good work with the Scotchbrite wheel
-
Thanks Sparky and everyone who has commented. I thought this project was going to take quite awhile but I am over 90% done. Some touch-up remains and the blade needs sharpened but it might be awhile before I dig out the Dremel tool so here is yet another update.
I rinsed the tool with hot water out of the ultrasonic because the vinegar is a acid and while it brightens the tool it also will cause it to rust. So after a quick shot of air here it is:

Other side:



Finally the closed shot:

It's not perfect but not bad. I need to blend around the one rivet on the LEATHERMAN side and some minor clean up remains but it really came out better than I expected. The file is what really surprised me, usually the file requires some work with the Dremel tool and a small wire brush but the file is nearly perfect.
I'm going to spray it with some CRC Marine 5-56 and put it in a clean jar to soak for Leatherman brown prevention.
More when I get around to working on it some more.
Bruce
-
I realized this is a great place to use Christian St. Clair's Nano Oil! I have used it on tools I want to keep so I put a small drop on every pivot and will put it back in the sun.
-
I'm really impressed with the finish on the handle that had been filed Bruce
Nice Job!

-
Great job Bruce.

-
Just read this thread ... you're a magician, Bruce

-
@sparky415 said:
I'm really impressed with the finish on the handle that had been filed BruceNice Job!

The finish is actually easy when you have the exact same Scotchbrite wheel as Leatherman! My wheel needed to be dressed or I would have gotten a more matte finish. But I thought the shiny might look good and it turned out to match the other handles when it was cleaned in the ultrasonic.
I actually had a couple of jars soaking in Marvel Mystery Oil for the past 3 or 4 weeks so I decided to open them up. I found 5 more Japan PST's, a Pocket Survival Tool, 2 PST's, 2 Surges, and 2 blunt nose Gerber 600's. So since I was already dirty....
The one Surge was sold to me cheap for parts because it would not close and the outer tools would not open. I pried all the internal tools open and the Surge closed! The outside opening tools opened easily and other than being dirty they seemed pretty good. I looked closer and it seemed like the internal tools would not go all the way down, looking a little closer and cheating by comparing to a good Surge I realized both handles were assembled backwards. So as soon as I get a chance I will take it apart for a complete rebuild or I have been thinking of a Recharge...maybe one with scissors and a saw/file exchanger...I wonder if the Surge awl will fit in a Charge?
Bruce
-
Wow! Great job
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login