Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Jeep light install

Scheduled Pinned Locked Moved The Break Room
111 Posts 1 Posters 8.0k Views
  1. Home
  2. Non Tool Forum
  3. The Break Room
  4. Jeep light install
Jeep light install
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Grant Lamontagne Offline
    Grant Lamontagne
    administrators
    Posts: 67,999
    Grant Lamontagne Offline
    Grant Lamontagne
    administrators
    wrote on last edited by
    #101 Quote Reply

      I did some research on the resistors and found they are pretty cheap and easy enough to install that even me, with my nonexistent electronical skills could manage. I just ordered ten of these:

      http://www.dx.com/p/6-ohm-50w-hid-led-warning-canceller-decoder-load-resistor-w-wire-connectors-golden-blue-148003#.U5w8x3ZaaSo

      I figure I will need four of them (2x front, 2x rear) and I imagine my boss will require a set as well since I also got him some LED signal replacements too.

      And, two extra to drop the price and in case I screw up a bit. :D

      Def

      EDC-TV
      SAKWiki
      GearFeed
      SAKSelector

      Merit Badges
      Charge Collector Reviewer Outdoor Cook MTO Tool BO Tools Level 3 Time Lord Level 3 One Piece Collector Airgun User Duct Tape Scale Changer EDC Pocket Dump Challenge Def's 50k Challenge Santa
      1 Reply Last reply
      • Cupboard Offline
        Cupboard
        Posts: 2,018
        Cupboard Offline
        Cupboard
        wrote on last edited by
        #102 Quote Reply

          You don't actually need the resistors, though it is one way to solve the problem.

          The better way to solve it is to get a better flasher unit that can cope with the LED indicator lights.
          One of the big advantage of LEDs is their reduced power consumption and putting in the resistors negates that.

          The other thing to bear in mind is that it shouldn't matter where you put the resistors because all the lights on one side are in parallel, so you could put all the resistors together in a a convenient location, whether that's by a light or not.

          1 Reply Last reply
          • Grant Lamontagne Offline
            Grant Lamontagne
            administrators
            Posts: 67,999
            Grant Lamontagne Offline
            Grant Lamontagne
            administrators
            wrote on last edited by
            #103 Quote Reply

              I was wondering about that. I figured the resistors just signed as much power as the incandescent bulb but converted it to heat.

              That's annoying. Still, at least I won't have to worry about following blown bulbs.

              Def

              Sent from a digital multitool

              EDC-TV
              SAKWiki
              GearFeed
              SAKSelector

              Merit Badges
              Charge Collector Reviewer Outdoor Cook MTO Tool BO Tools Level 3 Time Lord Level 3 One Piece Collector Airgun User Duct Tape Scale Changer EDC Pocket Dump Challenge Def's 50k Challenge Santa
              1 Reply Last reply
              • Grant Lamontagne Offline
                Grant Lamontagne
                administrators
                Posts: 67,999
                Grant Lamontagne Offline
                Grant Lamontagne
                administrators
                wrote on last edited by
                #104 Quote Reply

                  The LED fogs I put in before were cheap hunks of smurf and kind of crapped out on me, so I decided to invest in some better ones. I hope they last a lot better than the first set. :facepalm:

                  The old set was about $7 on ebay and these new ones were about $50, so I'm hoping that translates into a better quality bulb. Either that or I got taken. :ahhh

                  Here is a comparison of the old and new bulb.

                  <a href="http://s253.photobucket.com/user/Multitooldotorg/media/Personal/Jeepin/LED Light install/20140723_191309_zpsdgsbk7yx.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://gallery.multitool.org/pbmirror/Personal/Jeepin/LED Light install/20140723_191309_zpsdgsbk7yx.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                  And a comparison of them lit up- on the left is the new one, on the right is the old one.

                  <a href="http://s253.photobucket.com/user/Multitooldotorg/media/Personal/Jeepin/LED Light install/20140723_191422_zpsyqr4recs.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://gallery.multitool.org/pbmirror/Personal/Jeepin/LED Light install/20140723_191422_zpsyqr4recs.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                  And here are some better shots of the new and old ones:

                  <a href="http://s253.photobucket.com/user/Multitooldotorg/media/Personal/Jeepin/LED Light install/20140723_191507_zpsyltoszxb.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://gallery.multitool.org/pbmirror/Personal/Jeepin/LED Light install/20140723_191507_zpsyltoszxb.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                  <a href="http://s253.photobucket.com/user/Multitooldotorg/media/Personal/Jeepin/LED Light install/20140723_191511_zpswbn76b8o.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://gallery.multitool.org/pbmirror/Personal/Jeepin/LED Light install/20140723_191511_zpswbn76b8o.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                  <a href="http://s253.photobucket.com/user/Multitooldotorg/media/Personal/Jeepin/LED Light install/20140723_191518_zpsclwxvafn.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://gallery.multitool.org/pbmirror/Personal/Jeepin/LED Light install/20140723_191518_zpsclwxvafn.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                  <a href="http://s253.photobucket.com/user/Multitooldotorg/media/Personal/Jeepin/LED Light install/20140723_191520_zpsqejp4sjl.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://gallery.multitool.org/pbmirror/Personal/Jeepin/LED Light install/20140723_191520_zpsqejp4sjl.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                  And here is the pair of them now installed.

                  <a href="http://s253.photobucket.com/user/Multitooldotorg/media/Personal/Jeepin/LED Light install/20140723_191844_zpszpx3s0ym.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://gallery.multitool.org/pbmirror/Personal/Jeepin/LED Light install/20140723_191844_zpszpx3s0ym.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                  Let's hope these last better than the old ones. When I took out the old ones, the individual LED chips were falling off the frame. :facepalm:

                  Def

                  EDC-TV
                  SAKWiki
                  GearFeed
                  SAKSelector

                  Merit Badges
                  Charge Collector Reviewer Outdoor Cook MTO Tool BO Tools Level 3 Time Lord Level 3 One Piece Collector Airgun User Duct Tape Scale Changer EDC Pocket Dump Challenge Def's 50k Challenge Santa
                  1 Reply Last reply
                  • MadPlumbarian Offline
                    MadPlumbarian
                    Posts: 38,623
                    MadPlumbarian Offline
                    MadPlumbarian
                    wrote on last edited by
                    #105 Quote Reply

                      Well I guess we'll just have to wait till the sun goes down,, JR

                      "The-Mad-Plumbarian" The Punisher Of Pipes!!! JR
                      **As I sit on my Crapper Throne in the Reading Room and explode on the Commode, thinking, how my flush beat John’s and Jerry’s pair? Jack’s had to run for the Water Closet yet ended up tripping on a Can bowing and hitting his Head on the Porcelain God! **🚽
                      banner

                      Merit Badges
                      Mod User Scale Changer Photographer Camping Flashlight Outdoor Cook Scaler User Sporkman Paracord Hacker Fire Making Duct Tape Time Lord Level 3 ALOX with Scissors Hook User Carabiner User SAKMC Titanium MTo Store User Zip Tie User MTO Tool Chili Award Farmer X Challenge Advanced Modder
                      1 Reply Last reply
                      • Grant Lamontagne Offline
                        Grant Lamontagne
                        administrators
                        Posts: 67,999
                        Grant Lamontagne Offline
                        Grant Lamontagne
                        administrators
                        wrote on last edited by
                        #106 Quote Reply

                          In case anyone is wondering where all that mud on the Jeep came from, here are a few photos from the quick trail ride we did the other night.

                          Jeff's Jeep:

                          <a href="http://s253.photobucket.com/user/Multitooldotorg/media/Personal/Jeepin/20140721_191010_zpshabn1vws.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://gallery.multitool.org/pbmirror/Personal/Jeepin/20140721_191010_zpshabn1vws.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                          Mine:

                          <a href="http://s253.photobucket.com/user/Multitooldotorg/media/Personal/Jeepin/20140721_191403_zpsl84xkltu.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://gallery.multitool.org/pbmirror/Personal/Jeepin/20140721_191403_zpsl84xkltu.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                          A couple of bullfrogs in the mud hole:

                          <a href="http://s253.photobucket.com/user/Multitooldotorg/media/Personal/Jeepin/20140721_192339_zpsnyscusxo.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://gallery.multitool.org/pbmirror/Personal/Jeepin/20140721_192339_zpsnyscusxo.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                          <a href="http://s253.photobucket.com/user/Multitooldotorg/media/Personal/Jeepin/20140721_192401_zpsxxbsgtta.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://gallery.multitool.org/pbmirror/Personal/Jeepin/20140721_192401_zpsxxbsgtta.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                          Jeff's son managed to catch one:

                          <a href="http://s253.photobucket.com/user/Multitooldotorg/media/Personal/Jeepin/20140721_192737_zpsj8cs0f51.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://gallery.multitool.org/pbmirror/Personal/Jeepin/20140721_192737_zpsj8cs0f51.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                          It was a good time! :D

                          Def

                          EDC-TV
                          SAKWiki
                          GearFeed
                          SAKSelector

                          Merit Badges
                          Charge Collector Reviewer Outdoor Cook MTO Tool BO Tools Level 3 Time Lord Level 3 One Piece Collector Airgun User Duct Tape Scale Changer EDC Pocket Dump Challenge Def's 50k Challenge Santa
                          1 Reply Last reply
                          • Whoey Offline
                            Whoey
                            administrators
                            Posts: 12,658
                            Whoey Offline
                            Whoey
                            administrators
                            wrote on last edited by
                            #107 Quote Reply

                              @Grant Lamontagne said:
                              The LED fogs I put in before were cheap hunks of smurf and kind of crapped out on me, so I decided to invest in some better ones. I hope they last a lot better than the first set. :facepalm:

                              The old set was about $7 on ebay and these new ones were about $50, so I'm hoping that translates into a better quality bulb. Either that or I got taken. :ahhh

                              Here is a comparison of the old and new bulb.

                              <a href="http://s253.photobucket.com/user/Multitooldotorg/media/Personal/Jeepin/LED Light install/20140723_191309_zpsdgsbk7yx.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://gallery.multitool.org/pbmirror/Personal/Jeepin/LED Light install/20140723_191309_zpsdgsbk7yx.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                              And a comparison of them lit up- on the left is the new one, on the right is the old one.

                              <a href="http://s253.photobucket.com/user/Multitooldotorg/media/Personal/Jeepin/LED Light install/20140723_191422_zpsyqr4recs.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://gallery.multitool.org/pbmirror/Personal/Jeepin/LED Light install/20140723_191422_zpsyqr4recs.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                              And here are some better shots of the new and old ones:

                              <a href="http://s253.photobucket.com/user/Multitooldotorg/media/Personal/Jeepin/LED Light install/20140723_191507_zpsyltoszxb.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://gallery.multitool.org/pbmirror/Personal/Jeepin/LED Light install/20140723_191507_zpsyltoszxb.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                              <a href="http://s253.photobucket.com/user/Multitooldotorg/media/Personal/Jeepin/LED Light install/20140723_191511_zpswbn76b8o.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://gallery.multitool.org/pbmirror/Personal/Jeepin/LED Light install/20140723_191511_zpswbn76b8o.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                              <a href="http://s253.photobucket.com/user/Multitooldotorg/media/Personal/Jeepin/LED Light install/20140723_191518_zpsclwxvafn.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://gallery.multitool.org/pbmirror/Personal/Jeepin/LED Light install/20140723_191518_zpsclwxvafn.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                              <a href="http://s253.photobucket.com/user/Multitooldotorg/media/Personal/Jeepin/LED Light install/20140723_191520_zpsqejp4sjl.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://gallery.multitool.org/pbmirror/Personal/Jeepin/LED Light install/20140723_191520_zpsqejp4sjl.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                              And here is the pair of them now installed.

                              <a href="http://s253.photobucket.com/user/Multitooldotorg/media/Personal/Jeepin/LED Light install/20140723_191844_zpszpx3s0ym.jpg.html" target="_blank" rel="noopener noreferrer"><img src="http://gallery.multitool.org/pbmirror/Personal/Jeepin/LED Light install/20140723_191844_zpszpx3s0ym.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>

                              Let's hope these last better than the old ones. When I took out the old ones, the individual LED chips were falling off the frame. :facepalm:

                              Def

                              The seal on the old ones looks a bit dodgy... perhaps humidity getting in there? I hope you cleaned a bit before installing the new ones? might be worth looking at that it's properly sealed this time.

                              The difficult we do immediately, the impossible takes a little longer.

                              Merit Badges
                              Time Lord Level 3
                              1 Reply Last reply
                              • RimfireNZ Offline
                                RimfireNZ
                                Posts: 437
                                RimfireNZ Offline
                                RimfireNZ
                                wrote on last edited by
                                #108 Quote Reply

                                  Hey Geoff did you install HIDs in your main headlights? Or are they the ones mounted by the windscreen?

                                  I'm thinking about installing HIDs into my faculty housing on the hilux (somehow. It seems like a faff) and sticking a pair of HID spotlights linked up to the high beams too.

                                  1 Reply Last reply
                                  • gregozedobe Offline
                                    gregozedobe
                                    Posts: 5,148
                                    gregozedobe Offline
                                    gregozedobe
                                    wrote on last edited by
                                    #109 Quote Reply

                                      @Grant Lamontagne said:
                                      The LED fogs I put in before were cheap hunks of smurf and kind of crapped out on me, so I decided to invest in some better ones. I hope they last a lot better than the first set. :facepalm:

                                      The old set was about $7 on ebay and these new ones were about $50, so I'm hoping that translates into a better quality bulb. Either that or I got taken. :ahhh

                                      Def

                                      I was wondering what the beam pattern was like with the new LEDs ?

                                      For fog lights to work properly they need a very low, flat beam that goes out only below horizontal so the glare reflected from the water droplets that make up fog aren't dazzling you (and other drivers). The light emitted by LED "globes" is often quite different from regular filament globes, and unless the LEDs, reflector and lens are all designed to work together the results can be worse than well designed regular filament globes.

                                      babola: "Enjoy your tools and don't be afraid to air your opinion and feelings here, but do it in courteous and respectable way toward others, of course."

                                      1 Reply Last reply
                                      • Grant Lamontagne Offline
                                        Grant Lamontagne
                                        administrators
                                        Posts: 67,999
                                        Grant Lamontagne Offline
                                        Grant Lamontagne
                                        administrators
                                        wrote on last edited by
                                        #110 Quote Reply

                                          So far they seem fine. Oddly enough we haven't had a lot of fog lately to try them properly.

                                          Def

                                          Sent from a digital multitool

                                          EDC-TV
                                          SAKWiki
                                          GearFeed
                                          SAKSelector

                                          Merit Badges
                                          Charge Collector Reviewer Outdoor Cook MTO Tool BO Tools Level 3 Time Lord Level 3 One Piece Collector Airgun User Duct Tape Scale Changer EDC Pocket Dump Challenge Def's 50k Challenge Santa
                                          1 Reply Last reply

                                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                          With your input, this post could be even better 💗

                                          Register Login

                                          • 1
                                          • 2
                                          • 3
                                          • 4
                                          • 5
                                          • 6
                                          1. Home
                                          2. Non Tool Forum
                                          3. The Break Room
                                          4. Jeep light install
                                          Reply
                                          • Reply as topic
                                          Log in to reply
                                          COMMUNITY LINKS
                                          EDC-TV SAKWiki GearFeed SAKSelector
                                          Operational Funds

                                          Help us keep the Unworkable working!

                                          Make A Donation
                                          November Goal: $300.00
                                          Due Date: Nov 30
                                          Total Receipts: $0.00
                                          Below Goal: $300.00
                                          0% funded
                                          • Login

                                          • Don't have an account? Register

                                          • Login or register to search.
                                          • First post
                                            Last post
                                          0