firearms
-
I have heard a few club members make this statement:
"The 1911 was top of its game, back in 1912".
I puzzled over this statement until I saw an IPSC competition held at the club. I saw more 1911's jam during competition than I would care to see. I was and am still curious at shooting a .45 1911, but since that day, have put on the shelf my buying one to sate my curiosity. I plan to see if I can try someone else's 1911 down the road instead.
With that said, I have my IPSC course this weekend. Going to start tomorrow at 8 am sharp and go until 6ish, and repeat on Sunday. Looking forward to it, and also packing 700 rounds of factory 9 mm just in case I need it.

Also, I went back to the only local gun shop (and the only place I can buy re-loading stuff locally) to see if I could buy some components for my Dillon Square Deal B press. I quickly found out they had plenty of small primers, brass, and that is about it. I wanted to buy a digital scale...no go. I wanted to buy 115 grain bullets...no go (they only had cast lead bullets in 125 grains). I wanted to buy some accessories for the press...no go. Best yet, I wanted to buy some powder...no go. Looks like I may have to make another 3.5 hour drive to Sudbury to find something somewhat local.
I did find that my ultrasonic cleaner works nicely on spent brass. The water only didn't do that great a job, so I added a little jewelry cleaner to the mix. Next on my list is some brasso or something like that. I may or may not need a rotary tumbler down the road. I have an old rock tumbler somewhere, but I think it is well and truly buried under a lot of stuff. If memory serves me correct, it may be too small to be of much use anyways.
-
@Chako said:
I have heard a few club members make this statement:"The 1911 was top of its game, back in 1912".
I puzzled over this statement until I saw an IPSC competition held at the club. I saw more 1911's jam during competition than I would care to see. I was and am still curious at shooting a .45 1911, but since that day, have put on the shelf my buying one to sate my curiosity. I plan to see if I can try someone else's 1911 down the road instead.
With that said, I have my IPSC course this weekend. Going to start tomorrow at 8 am sharp and go until 6ish, and repeat on Sunday. Looking forward to it, and also packing 700 rounds of factory 9 mm just in case I need it.

Also, I went back to the only local gun shop (and the only place I can buy re-loading stuff locally) to see if I could buy some components for my Dillon Square Deal B press. I quickly found out they had plenty of small primers, brass, and that is about it. I wanted to buy a digital scale...no go. I wanted to buy 115 grain bullets...no go (they only had cast lead bullets in 125 grains). I wanted to buy some accessories for the press...no go. Best yet, I wanted to buy some powder...no go. Looks like I may have to make another 3.5 hour drive to Sudbury to find something somewhat local.
I did find that my ultrasonic cleaner works nicely on spent brass. The water only didn't do that great a job, so I added a little jewelry cleaner to the mix. Next on my list is some brasso or something like that. I may or may not need a rotary tumbler down the road. I have an old rock tumbler somewhere, but I think it is well and truly buried under a lot of stuff. If memory serves me correct, it may be too small to be of much use anyways.
I usually buy all components on-line except for those with a $ hazard charge $ (powder and primers). There has been issues with finding powder and primers in recent years with the ammo scares. I can usually find what I want at gun shows. If you are talking about practice ammo or competition handgun ammo, you might consider copper plated bullets. They are very well priced and you can buy them on-line. I recently bought some from this company, they have good prices, cheap shipping and you can buy from them directly.
http://www.xtremebullets.com/9mm-s/9666.htm
I would look at MidwayUSA, Brownells or other on-line sources for electronic scales.
-
The reason those 1911's are jamming during competition is that they're too tight. Pick up an issue .45 and it will rattle. Those loose tolerances are what keeps them running. There's a reason that the US military kept them as standard issue for 71 years, and they're still seeing combat 103 years later.......
-
@jerseydevil said:
The reason those 1911's are jamming during competition are that they're too tight. Pick up an issue .45 and it will rattle. Those loose tolerances are what keeps them running. There's a reason that the US military kept them as standard issue for 71 years, and they're still seeing combat 103 years later.......+1 Other non standard things like heavy recoil springs (messes up the mechanical timing of the design causing the extractor to ride over the rim), barrel bushings fitted too tightly etc. I been shooting 1911's since 1976 and I can count jams on one hand. Most were due to worn out mags or crummy reloads....then there was that match where I was hip shooting though a cut square in a plywood barrier....held too high and my rear sight clipped the plywood during recoil...that caused a stoppage.

There are a lot of good pistol designs out there but for me, the 1911 is still the most natural pointing and easiest to shoot accurately...

-
@Chako said:
I have heard a few club members make this statement:**"The 1911 was top of its game, back in 1912". **
Who ever is making that statement is showing their ignorance. That sounds real tough down at the club with the boys but is bravo sierra in the real world. I use to shoot a little IDPA at a local range for fun. For me it was just fun and extra pratice. I'm not very competitive by nature. One day one of the young studs asked me where I learned to shoot like that. He said your not the fastest shot out here but you dont miss. My reply was I learned a long time a go you cant shoot fast enough to make up misses and if you lay your shooting foundations correctly and maintain them the rest will follow. I was shooting a stock Springfield 1911 Loaded. I cut my teeth reading gun cranks like Elmer Keith, Col. Charlie Askins, Jeff Cooper, Bill Jordon, Skeeter Skelton etc.. As Clint Smith says shoot till your happy! :)
-
Jeff Cooper would approve of your 1911 David. Mr. Keith and Mr. Skelton , however...... ;)
-
@jerseydevil said:
Jeff Cooper would approve of your 1911 David. Mr. Keith and Mr. Skelton , however...... ;)Tom I just happen to have a few revolvers those gentelmen would approve of. :D
-
I have heard a few club members make this statement:
**"The 1911 was top of its game, back in 1912". **
Who ever is making that statement is showing their ignorance. That sounds real tough down at the club with the boys but is bravo sierra in the real world. I use to shoot a little IDPA at a local range for fun. For me it was just fun and extra pratice. I'm not very competitive by nature. One day one of the young studs asked me where I learned to shoot like that. He said your not the fastest shot out here but you dont miss. My reply was I learned a long time a go you cant shoot fast enough to make up misses and if you lay your shooting foundations correctly and maintain them the rest will follow. I was shooting a stock Springfield 1911 Loaded. I cut my teeth reading gun cranks like Elmer Keith, Col. Charlie Askins, Jeff Cooper, Bill Jordon, Skeeter Skelton etc.. As Clint Smith says shoot till your happy! :)
Gee, we grew up reading the same authors...
My guns are stock except for aftermarket grips and one has a Brown Precision Solid Barrel Bushing (in place of the Colt collet bushing). -
Forgot to post this the other day I think.
Even though I have had a CCW non stop for over 10 years in other states. Former law enforcement officer and over 25 years in the military I still had to take a class in Texas for there CCW.
Oh well any excuse to shoot is ok by me.
Took the new CZ P 07 with trigger work by Cajun Gun Works. Best pistol trigger I have ever used by far.

Brought Lovechild along just in case but she was not needed.

The course of fire was easy with shots from 3,7 and 15 yards. Perfect score in case you was wondering.
-
I guess one can either be a 1911 fan or not. Either way, I do want to try one very much. I have tried a .40 and didn't much care for it. Mind you, that was my very first pistol to try and I was startled at how violent the kick was. I much prefer the 9 mm. I haven't tried a 45 yet. I was told by several folks that the 45 is much more pleasant to shoot than the 40.
Harley, nice CZ.
-
Just got back from another visit to the local gun shop. This time, the owners were around and it appeared that they had everything I was looking for yesterday...just that their employee didn't know anything in regards to stock.
I took their last powder, a 1lb Hodgdon HP-38 container. I also bought 1 package of cast lead 115 grain bullets in 500 quantity to get me started. She was telling me that the 124 grain bullet would take less powder...something to consider on my next bullet buy. I also bought 1000 Winchester small primers, a Hornady rotary tumbler, corn cob medium, a bottle of medium rejuvenation, and an electronic scale accurate to 0.1g. Get this, they had them in the archery area to weight arrows.

Now all I need to do is after my course this weekend, figure where to install my press upstairs, go buy two or so bolts to install it, and I should be in business after a little room cleaning.

I was told that those steel Russian 9 mm casings I lovingly picked up and cleaned may not work in the press. I bought two bags of 100 brass casings just in case. I also have some shot once Remington brass. So worse case scenario, I should have around 400 spent casings. Going to try one of those metal casings when I can...so I won't throw them out just yet.
Does anyone know if those metal 9 mm cases will work, or should I just toss them and focus on the brass?
-
Brass. Never heard of steel cases reloaded....no elasticity like brass.
-
Last two Colt 1911s I had didn't work new out of the box. One of them wouldn't even chamber; had an undersized breach face that wouldn't allow a round to chamber. Obviously never test fired. That pretty much soured me on both 1911s and Colt. Did shoot a Kimber 1911 a few years back. Very nice, but not enough to buy one.
One of the local ranges had a CZ P07 for rent. Shot it a number of times. Very accurate and dead-on. So picked one up. Mine had groups 3-4 times larger and substantially low and to the left. Some times I'm snake-bit. So back to the CZ 75 Shadow and the HK USP.
-
Got it. Going to do something with the steel ones then. I won't waste my time with them from now on. I am going to use the rest of my Russian ammo for my black badge course...so I won't have to worry about picking them up. Guess I won't be saving a few bucks buying Barnaul 9 mm in the future from this point on.

-
@ColoSwiss said:
Last two Colt 1911s I had didn't work new out of the box. One of them wouldn't even chamber; had an undersized breach face that wouldn't allow a round to chamber. Obviously never test fired. That pretty much soured me on both 1911s and Colt. Did shoot a Kimber 1911 a few years back. Very nice, but not enough to buy one.One of the local ranges had a CZ P07 for rent. Shot it a number of times. Very accurate and dead-on. So picked one up. Mine had groups 3-4 times larger and substantially low and to the left. Some times I'm snake-bit. So back to the CZ 75 Shadow and the HK USP.
I had heard some stuff about Colt...very sad. Mine are Early 80's-90's and the bulk of mine in the past were Series 70's guns. Out of 20+ Colt 1911s (Govts, Commanders and Gold Cups), never a bad one...never.
I strayed and bought a different 1911 brand only once....the old timers will probably remember MS Safari Arms. Shot three rounds out of it....on the 3rd shot, the front red insert flew out and the hammer fell to half cock. It went back the next day and I had my traded in stock Government Model back in my hands.
Now, that ain't to say I didn't mix in some Browing HPs, Smiths, Colts and Rugers occasionally! :D
-
@captain spaulding said:
Brass. Never heard of steel cases reloaded....no elasticity like brass.
This. ^^^
Just toss the steel case stuff.
Getting steel cases stuck in your nice new SDB won't be enjoyable. Throw them away. I wouldn't recommend reloading aluminum cases either. 9mm brass is easy to come by, perhaps the easiest brass to find.
-
Last two Colt 1911s I had didn't work new out of the box. One of them wouldn't even chamber; had an undersized breach face that wouldn't allow a round to chamber. Obviously never test fired. That pretty much soured me on both 1911s and Colt. Did shoot a Kimber 1911 a few years back. Very nice, but not enough to buy one.
One of the local ranges had a CZ P07 for rent. Shot it a number of times. Very accurate and dead-on. So picked one up. Mine had groups 3-4 times larger and substantially low and to the left. Some times I'm snake-bit. So back to the CZ 75 Shadow and the HK USP.
I had heard some stuff about Colt...very sad. Mine are Early 80's-90's and the bulk of mine in the past were Series 70's guns. Out of 20+ Colt 1911s (Govts, Commanders and Gold Cups), never a bad one...never.
I strayed and bought a different 1911 brand only once....the old timers will probably remember MS Safari Arms. Shot three rounds out of it....on the 3rd shot, the front red insert flew out and the hammer fell to half cock. It went back the next day and I had my traded in stock Government Model back in my hands.
Now, that ain't to say I didn't mix in some Browing HPs, Smiths, Colts and Rugers occasionally! :D
Had a Series 70 9mm that was so accurate I had custom sights installed. Decided in a weak moment it was too large and heavy for the load and the mag capacity, so sold it. :ahhh
The CZ Shadow came along later and is a good replacement. Live and learn (sometimes).
-
Last two Colt 1911s I had didn't work new out of the box. One of them wouldn't even chamber; had an undersized breach face that wouldn't allow a round to chamber. Obviously never test fired. That pretty much soured me on both 1911s and Colt. Did shoot a Kimber 1911 a few years back. Very nice, but not enough to buy one.
One of the local ranges had a CZ P07 for rent. Shot it a number of times. Very accurate and dead-on. So picked one up. Mine had groups 3-4 times larger and substantially low and to the left. Some times I'm snake-bit. So back to the CZ 75 Shadow and the HK USP.
I had heard some stuff about Colt...very sad. Mine are Early 80's-90's and the bulk of mine in the past were Series 70's guns. Out of 20+ Colt 1911s (Govts, Commanders and Gold Cups), never a bad one...never.
I strayed and bought a different 1911 brand only once....the old timers will probably remember MS Safari Arms. Shot three rounds out of it....on the 3rd shot, the front red insert flew out and the hammer fell to half cock. It went back the next day and I had my traded in stock Government Model back in my hands.
Now, that ain't to say I didn't mix in some Browing HPs, Smiths, Colts and Rugers occasionally! :D
Had a Series 70 9mm that was so accurate I had custom sights installed. Decided in a weak moment it was too large and heavy for the load and the mag capacity, so sold it. :ahhh
The CZ Shadow came along later and is a good replacement. Live and learn (sometimes).
The CZ designs are solid...always wanted to try a 75!

-
@captain spaulding said:
Took apart the Remington 870 shotgun tonight and boy, what a mess it was. Learning quickly that sometimes, the local gun shop is a mess. I got the shotgun back from the local shop after they had to use a Dremel on two dimples inside the magazine tube. Once gone, it allows full access to the extension tube.
Well, got the shotgun back and took it out to the range, and damaged the second factory red dot sight. Noted after a few rounds something was really off. It felt like there was a lot of sand in it. I quickly stopped and thought to myself...no he didn't did he?
Well tonight was the first time I was able to take it apart. Man oh man, you should have seen the metal shavings. The local shop Dremeled away the two dimples alright, without taking the magazine tube off, or shoving any thing in the tube to catch metal shavings. Consequently, all that crap went into the action.

After a good half hour of TLC, the shotgun is feeling better than ever. To whoever did that to my shotgun....

All I keep hearing from you is people at the gun stores doing idiotic things to your guns or just plain acting like dumb asses. If I were you I would stay far away from having anyone work on your firearms unless it is completely necessary. I'm not lecturing you, but you should be doing these simple things yourself. Again, I am not trying to be rude.
Maybe I don't get out much, but don't hear too many gunsmith horror stories in my parts. A bad gunsmith can ruin the rep of a shop and destroy the business pretty quickly. I'm sure there's always gonna be unhappy customers, but this kind of thing is really surprising to me.
Sent from my iPhone using Tapatalk
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login