Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

Hemi with broken spring

Scheduled Pinned Locked Moved The Break Room
5 Posts 1 Posters 589 Views
  1. Home
  2. Non Tool Forum
  3. The Break Room
  4. Hemi with broken spring
Hemi with broken spring
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • firefightingjosh Offline
    firefightingjosh
    Posts: 294
    firefightingjosh Offline
    firefightingjosh
    wrote on last edited by
    Quote Reply

      Bought a beautiful 2003 2500 that's fully loaded and that has the 5.7 hemi. Of course this is the year of the common broken valve spring and this truck joined the club with the previous owner. I bought it assuming worst case I'd throw a new long block in her. Got the head off and to my surprise the valve was hardly bent and the piston has just a tiny mark. So with that, I'm pulling both heads and either getting them rebuilt or ordering rebuilt ones and sending mine in. My question is, this truck has 156, 000miles on it and I figured since I have the heads off I could slap a new wp, timing chain and plug wires in. Anything else I should do? Anyone know of a good company for heads? I definitely want the updated Springs, and seats. I don't know much about the 3rd Gen rams, but 156k isn't to much is it? I only paid 3k for her, and had planned to fix and sell her but I kinda like her lol.

      Josh

      1 Reply Last reply
      • Mr. Whippy Offline
        Mr. Whippy
        Posts: 12,208
        Mr. Whippy Offline
        Mr. Whippy
        wrote on last edited by
        #1 Quote Reply

          I don't know this particular vehicle but IN GENERAL:

          If you're pulling both heads (which I would do), besides doing the valves/guides and springs, you might want them to polish the ports, for more consistent fuel/air flow.

          It might be worth looking at the cams and cam lobes to make sure there wasn't damage to the surface when the valve was bent.

          Also, if it's easy to access, (and you're doing the work yourself), you might want to just replace the oil pump or at least clean the screen.

          Also, if it's a manual tranny AND the engine is out, it's a quick and easy time to replace the clutch and have the flywheel turned. Not really necessary, but again, if it's already out, it's a good time to do it, rather than pulling the engine later for the same service (156,000 miles and all...)

          1 Reply Last reply
          • Grant Lamontagne Offline
            Grant Lamontagne
            administrators
            Posts: 67,999
            Grant Lamontagne Offline
            Grant Lamontagne
            administrators
            wrote on last edited by
            #2 Quote Reply

              Got to agree with Mr. Whippy on this one. Sounds like he has pretty well everything thought out, almost like he's done this a time or two. .... :ahhh

              I'd look at the airflow through the entire system- look at the intake, filter(s), manifolds, catalytic converter, exhaust and muffler. If anything is damaged, cracked or blocked it could be robbing you of a serious amount of power and eating a lot more fuel. It might be worth it to upgrade any components that might not be 100%.

              I'd also check the balance on the radiator fans.

              Def

              EDC-TV
              SAKWiki
              GearFeed
              SAKSelector

              Merit Badges
              Charge Collector Reviewer Outdoor Cook MTO Tool BO Tools Level 3 Time Lord Level 3 One Piece Collector Airgun User Duct Tape Scale Changer EDC Pocket Dump Challenge Def's 50k Challenge Santa
              1 Reply Last reply
              • Mr. Whippy Offline
                Mr. Whippy
                Posts: 12,208
                Mr. Whippy Offline
                Mr. Whippy
                wrote on last edited by
                #3 Quote Reply

                  @Grant Lamontagne said:
                  Got to agree with Mr. Whippy on this one. Sounds like he has pretty well everything thought out, almost like he's done this a time or two. .... :ahhh

                  ::)

                  Actually, I did this exact thing with my first Land-Rover. Except the valve went through the piston and was setting in the oil pan.

                  Almost had to do this on my Ducati Multistrada. Unfortunately parts and machining was so expensive, it wasn't really feasible.

                  1 Reply Last reply
                  • firefightingjosh Offline
                    firefightingjosh
                    Posts: 294
                    firefightingjosh Offline
                    firefightingjosh
                    wrote on last edited by
                    #4 Quote Reply

                      Thanks guys, definitely plan and going through the truck while I wait for the heads to be rebuilt and ported and polished

                      Josh

                      1 Reply Last reply

                      Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                      Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                      With your input, this post could be even better 💗

                      Register Login

                      1. Home
                      2. Non Tool Forum
                      3. The Break Room
                      4. Hemi with broken spring
                      Reply
                      • Reply as topic
                      Log in to reply
                      COMMUNITY LINKS
                      EDC-TV SAKWiki GearFeed SAKSelector
                      Operational Funds

                      Help us keep the Unworkable working!

                      Make A Donation
                      November Goal: $300.00
                      Due Date: Nov 30
                      Total Receipts: $0.00
                      Below Goal: $300.00
                      0% funded
                      • Login

                      • Don't have an account? Register

                      • Login or register to search.
                      • First post
                        Last post
                      0