EDC Experiments
-
@ToolJoe said:
Would a pair of electrician scissors work to cover wire cutting needs? ...I want to be able to cut a 3-conductor, 16 gauge AC line cord as well as 12 ga. solid copper wire. Most 4 inch pliers multitools (e.g., Rebar, Spirit, SOG PPP) can do that, but I'm exploring carrying a few individual tools instead of a multitool.
I have electricians scissors. They are good for small gauge telecom wire cuts and weigh about 3 ounces (hefty).
-
I've been looking for a multi bit pocket screwdriver which takes 1/4 inch bits like that Suzo Happ. Thanks for finding it. One point of confusion in the Amazon description is that the driver comes with a 3/8" (not 1/4") nutdriver.
I had noted a similar pocket driver at http://pocketscrewdrivers.com , but it looks like you must buy them in quantities of 150 or more:

-
That's not the one I ordered. It's this one.
-
If I were Leatherman I'd put a LM bit driver on everything they make - maybe even flashlights. It's a way to tie a customer into their ecosystem and make everyone want to have bits and accessories.
-
Never mind, that is what it says - 3/8' driver. Dang! I wasn't paying attention.
-
I'm looking right at it, and those definitely look like 1/4" bits, not 3/8". In fact I don't think I've ever seen 3/8" bits. I found it on two other sites with the same stock description though. I think it's a typo. Those screwdriver heads would have to be massive if they were 3/8".
-
It arrives tomorrow, so I'll tell you what it is then.
-
Forgot I have the bit driver Crater too. No need to carry the bit kit.

-
Great thread, Tom.

-
Thanks!
-
Parnass, I got the bit driver in. It's definitely 1/4". It's quite a bit bigger than the Craftsman driver. Here's a comparison along with the other drivers I got in and a Wave for scale.

-
It does fit into the sheath with the Cobra where the Craftsman driver was.
-
I wish these little drivers had a hex shaft or fitting above the bit or on the end so we could put a wrench on them for more torque.
-
This is very nice thread. It even convinced me to snag a pair of Cobra pliers.
good stuff. Very lightweight -
Glad you're getting something out of it!
-
I'm favoring the Screwpop driver over the Suzo Happ and True Utility MiniDriver. It has better leverage and is nice and small. The bit is a little loose in the socket, and the magnet was out when I got it and had to be glued back in. Actually I should have left it out and used the Klein double-ended bits with their ball bearing to hold them in - probably would have worked better. The True Utility is nice and small, but you have to take out a bit to put a quarter or key in the slot on the driver to get leverage, and that will probably lead to losing bits since they are shorter than normal and black.
-
Just made my EDC sheath a lot smaller. I got in the Leatherman Piranha 2, and if this works I now have cut down my tools to a lot smaller profile by combining the crescent wrench functions, screwdriver, and prybar into one tool (actually 2 with the driver extension.)



-
Just throwing this out there for giggles: http://chapmanmfg.com/collections/new-tools/products/famous-midget-ratchet-cm-13
-
@Tom Munch said:
Just made my EDC sheath a lot smaller. I got in the Leatherman Piranha 2, and if this works I now have cut down my tools to a lot smaller profile by combining the crescent wrench functions, screwdriver, and prybar into one tool (actually 2 with the driver extension.)I forever fight the battle between "ease of carry" versus "ease of use".
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login