Sharpening, discuss.
-
@Sparky415 said:
I understand that perfectly, if you are outside get the sun behind you ;)That's good advice.

I also find a magnifying glass helps me a lot (but that’s just me :-[ )
I bought a small loupe/jeweler's magnifier, but haven't figured out how to use it effectively when sharpening. So, I have ended up prefering a magnifying glass. :)
-
Another Spyderco Sharpmaker fan. Works on everything I need to sharpen.
-
I am a sharpening noob.

Me too. :D
I've got a Lanksy Standard 3-stone set and while it's good for deep blades it's a PITA for SAKs. Mostly I just use the stones freehand, and try to gauge the angle by eye. I've also got a Victorinox pocket sharpener which is only good for touch ups and serrations. I reckon a Sharpmaker would suit me better, but I can't really see the difference between that and spending 1/3 of the cost of the Spyderco on a Lanksy 4-rod turnbox.
I have an Swisstool but the blade is the same as a SAK.
I use the slanky sharpening system, it works the same as the sharpmaker.
But it is a a third of the price.Gets it razor sharp, and works just as good as the sharpmaker of a friend of mine.
I never had succes with a stone, probably because i have a crappy stone, but the lansky system/sharpmaker has a set angle. It is much easier and gets it hair popping sharp.
Is this what you use ?
http://lansky.com/index.php/products/4-rod-turn-box/ -
I am a sharpening noob.

Me too. :D
I've got a Lanksy Standard 3-stone set and while it's good for deep blades it's a PITA for SAKs. Mostly I just use the stones freehand, and try to gauge the angle by eye. I've also got a Victorinox pocket sharpener which is only good for touch ups and serrations. I reckon a Sharpmaker would suit me better, but I can't really see the difference between that and spending 1/3 of the cost of the Spyderco on a Lanksy 4-rod turnbox.
I have an Swisstool but the blade is the same as a SAK.
I use the slanky sharpening system, it works the same as the sharpmaker.
But it is a a third of the price.Gets it razor sharp, and works just as good as the sharpmaker of a friend of mine.
I never had succes with a stone, probably because i have a crappy stone, but the lansky system/sharpmaker has a set angle. It is much easier and gets it hair popping sharp.
Is this what you use ?
http://lansky.com/index.php/products/4-rod-turn-box/Yup, that's the one.
For longer knives the rods may be a bit short but there is also a version with longer rods. For SAKs, MTs and bushcraft knives it works fine.Machetes may be a different story ???
-
I have a spiderco system and a lansky. However, I find myself to be better with basic whetstones then stropping with green paste, linen and leather. I originally learned on stones, the strop is more just the past year or so as I use a straight razor as well. Keeps things SHARP...
-
I am another disciple of the Sharpmaker. I have had several different stones etc. and have found the Sharpmaker to be easy to use, fairly quick, and obtain consistent shaving sharp edges with it!
-
I use my Sharpmaker to keep blades sharp but sometimes you need to create a new bevel and for this I use a Lansky or Warthog Multi edge.
http://www2.knifecenter.com/item/LSLKC03/Lansky-Standard-Knife-Sharpening-System
http://www2.knifecenter.com/item/WOWHS19/warthog-sharpeners-multi-edge-220
I use the Spyderco 99 times out of 100.
I went to a custom maker friend of mine last week to put a new bevel on my beater Endura, so much quicker with a belt grinder.
I also keep this little thing handy for SAKs
http://www2.knifecenter.com/item/LSLCKEY/Lansky-inchThe-Mini-inch-Crock-Stick-Knife-Sharpener -
wet stone and diamond stone user here.
I also have a mini lanksy ceramic rod for fast adjustments.
My father learn me how to sharpen on stone, i've improve his technique (he use a stone in left hand and knife in right hand, the angle isn't constant) and the used stones (he stop at 600 grit). -
When a knife gets too dull I just buy a new one.

Def
-
So there are a lot of different ways to sharpen your knives.
But the other question that should have been asked is how sharp do you make your knives.
Someone who is sharpening his knife with a strop wants it much sharper than someone who spends 20 seconds a week with a lansky sharpenIng kit.
Also blade steel is a big factor, softer steel gets touched up quick to razor sharpness and sv30 takes longer but holds that edge longer.I have a Swisstool so i have the regular SAK blade steel.
I dull my blade pretty quick because i sometimes cut material that is not supposed for a SAK blade. (Plastic bottles carpet etc..)
But most of the time bananas, apples, rope and i always cut the curry and mayo bottles open to get the last out.
I sharpen my knife once a week and do this on a cheap lansky sharpening system.
I make it hair popping sharp with the white ceramic rods.
I first Clean of all the gunk of the knife blade and then pull it about ten times over the lansky system.Then it is good for another week.

-
I've been on both sides of the fence with sharpening. I used to want all my knives surgical sharp then sharp enough now I'm back to hair popping sharp.
I enjoy the process as much as the results however removing steel is not something I take lightly. Stropping for me is a great way to keep my SAKs ready to go as well as my MT blade without shortening the life of the knife.
-
@Aloha007 said:
I've been on both sides of the fence with sharpening. I used to want all my knives surgical sharp then sharp enough now I'm back to hair popping sharp.I enjoy the process as much as the results however removing steel is not something I take lightly. Stropping for me is a great way to keep my SAKs ready to go as well as my MT blade without shortening the life of the knife.
Stropping is so easy, everyone should be doing it. If not for the sharpness of the blade, then the therauputic benefit of the act itself
-
@Luna Knife said:
I've been on both sides of the fence with sharpening. I used to want all my knives surgical sharp then sharp enough now I'm back to hair popping sharp.
I enjoy the process as much as the results however removing steel is not something I take lightly. Stropping for me is a great way to keep my SAKs ready to go as well as my MT blade without shortening the life of the knife.
Stropping is so easy, everyone should be doing it. If not for the sharpness of the blade, then the therauputic benefit of the act itself
Yes but you can also over do it and round over the edge. The same could be said about using deburring sticks (rounding over, actually dulling the new edge) and destressing the edge (it takes away a lot of metal and one should be adequate at sharpening and using low grit stones)
-
@Luna Knife said:
I've been on both sides of the fence with sharpening. I used to want all my knives surgical sharp then sharp enough now I'm back to hair popping sharp.
I enjoy the process as much as the results however removing steel is not something I take lightly. Stropping for me is a great way to keep my SAKs ready to go as well as my MT blade without shortening the life of the knife.
to overdo stropping it must take 1000 strokes. I do 15-20 max.
You can use leather, cardboard, denim or even your hairy arm
Stropping is so easy, everyone should be doing it. If not for the sharpness of the blade, then the therauputic benefit of the act itself
Yes but you can also over do it and round over the edge. The same could be said about using deburring sticks (rounding over, actually dulling the new edge) and destressing the edge (it takes away a lot of metal and one should be adequate at sharpening and using low grit stones)
-
We need kwakster here...
I also use the Sharpmaker. Its easy to use and gives great results.

-
I use a Young's (I think I got the brand right) pocket sharpener I got at an estate sale nib. It is primarily for arrow heads but also had a sharpener for knives.
-
@Luna Knife said:
I've been on both sides of the fence with sharpening. I used to want all my knives surgical sharp then sharp enough now I'm back to hair popping sharp.
I enjoy the process as much as the results however removing steel is not something I take lightly. Stropping for me is a great way to keep my SAKs ready to go as well as my MT blade without shortening the life of the knife.
Stropping is so easy, everyone should be doing it. If not for the sharpness of the blade, then the therauputic benefit of the act itself
Yes but you can also over do it and round over the edge. The same could be said about using deburring sticks (rounding over, actually dulling the new edge) and destressing the edge (it takes away a lot of metal and one should be adequate at sharpening and using low grit stones)
Very good points. I've rounded the edge when I first started stropping. I scratched my head wondering what happened. As with all sharpening patience and experience is key.
-
It depends on how dull the blade is.
-For a really dull blade, I use a diamond flat: coarse, then fine. Then, I use a crock stick (fine ceramic rod) to get it sharp. If I want it to pop hairs (for example, you don't want an axe or machete that sharp) then I strop it with the back side of a leather belt loaded with polishing compound. Finally, a strop on a glossy magazine cover gets it hair-popping.
-For a semi-sharp blade or just a touch-up, you can eliminate the first step or two, then proceed as I do.Everything is done freehand; no angle guides or machines. Most of my EDC blades have a 15-degree angle per side, but some go down to 10-degrees per side. Multi-tool blades are fine at 20-degrees per side.
-
@Luna Knife said:
@Luna Knife said:
I've been on both sides of the fence with sharpening. I used to want all my knives surgical sharp then sharp enough now I'm back to hair popping sharp.
I enjoy the process as much as the results however removing steel is not something I take lightly. Stropping for me is a great way to keep my SAKs ready to go as well as my MT blade without shortening the life of the knife.
Stropping is so easy, everyone should be doing it. If not for the sharpness of the blade, then the therauputic benefit of the act itself
Yes but you can also over do it and round over the edge. The same could be said about using deburring sticks (rounding over, actually dulling the new edge) and destressing the edge (it takes away a lot of metal and one should be adequate at sharpening and using low grit stones)
**to overdo stropping it must take 1000 strokes. I do 15-20 max.
You can use leather, cardboard, denim or even your hairy arm**
exactly. still there are individuals who are self proclaimed experts that spend hours on stropping and set that as an example.
as far as medium goes, leather and cardboard are my top choice. true you can do it on your arm, but after a few cuts, i'm simply not a fan
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login