3D Printer Blog
-
Looking good.
I regret not making better notes of my various settings and tricks for good results with various materials when I had them up and running well. It might be a good idea to do better than me at that.. :D
With some luck I'll get to make a little design or two later this summer where the end products are actually made on the filament 3D printer. That might get interesting.
-
I was a bit annoyed with the CR-100. I bought it as a lark because it was just darn cute. Annoyed that I couldn't get anything to stick. Now I have 2 viable 3D printers. Makes me happy.
Good point on taking notes.

-
@Chako said:
I bought it as a lark because it was just darn cute.Ah, I struggle with that issue too. I'll have to avoid tool shops when that small Knipex Cobra comes around. Or more likely, just accept my destiny and get it over with. Knowing Knipex I'd likely have to eat pasta for week as a financial plan. (Someone is screaming no more pasta in the background - I might need a new financial model! :D )
-
while I don't have a printer I had seen some articles that hinted that enclosures help with both noise and temp issues. As you seem to have realized.
-
I wanted to print a vase as something large and interesting to do. I found quite a few over at thingiverse, and decided to pull a nice model from there and print it. I import it into Cura 4.6.1 and found that after slicing it, it is solid. I went online to find out how to print this correctly. I located a setting called "spiralize outer countour". Apparently this will print any object with single wall thickness with a bottom and no top. Perfect. However, it took me several articles online to figure out how to activate it. You have to go into Cura settings and check a box among the hundreds of other boxes (found under specialized mode section). Once check-marked, the option comes up and enables you to print a vase. After activating this and slicing the model, it looks good to go. I am now printing it in black PLA, and am very curious to see if this print will work.
-
So far so good. Currently at 24% completed. I have found the glue stick works best when I flip over the glass plate to print on the smooth side.
<a href="https://flic.kr/p/2jaeSXG" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49987670718_3206460004_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8556A by Chako, on Flickr
-
Came out good. I was worried taking it off of the glass plate because the wall is very thin. I ran the glass plate under water and that did the trick. It popped off relatively easy.
<a href="https://flic.kr/p/2janEK7" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49989190516_fe4a5d7059_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8559A by Chako, on Flickr
-
@Chako said:
Came out good. I was worried taking it off of the glass plate because the wall is very thin. I ran the glass plate under water and that did the trick. It popped off relatively easy.<a href="https://flic.kr/p/2janEK7" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49989190516_fe4a5d7059_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8559A by Chako, on Flickr
Single pass thickness? That does sound thin! :ahhh
-
Agreed. Surprisingly enough, I filled it with water and it did not leak.That to me is a miracle. It does make a nice decorative piece. I am printing a different model right now.
-
The latest print using the spiralize outer contour mode.
<a href="https://flic.kr/p/2jaHQy1" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/49993125752_08e0b546ad_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8571A by Chako, on Flickr
-
You certainly seem to keep your printers busy!
-
I really like that last one. Do you happen to have a link to it?
-
Printing out a retro rocket model right now.
If I had known how much fun having a 3D printer would be..I would have gotten one sooner.
-
And the completed rocket in black PLA. I scaled it larger from the original print size. I think it turned out very nice.
<a href="https://flic.kr/p/2jbktoN" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50000078606_92287b8eb8_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8581A by Chako, on Flickr
This model did not require any supports.
-
I took my time and I did it. The task was easy but harder because of the lack of good instructions. I was forced to watch multiple videos on how to install a BigTreeTech TFT35 E3 V3.0 and the BigTreeTech SKR Mini E3 V1.2 before starting this upgrade. I was a bit worried to bork something up during the install. I had my tablet next to me and I paused a few key videos during this install.
I started off with the screen upgrade. It wasn't at all clear on which video port to use. There were 3. I figured I woud install the screen and test it out on the board that came with the printer, but quickly found out after digging deeper in the lack of literature, that I could not activate touch screen with the Creality board.

With that in mind, then I had to figure out which cables go where, and did the motherboard upgrade at the same time.Apparently, you only need to use port 3 and the serial port on both as they were both BigTreeTech parts. Otherwise, i would have had to use only Port 1 or 2 on the LCD screen to the LCD port on the Creality main board. A simple sentence or two explaining this would have caused a lesser sense of confusion.
Here is the original Creality main board. It is V 1.1.4.
<a href="https://flic.kr/p/2jd4adq" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50019528652_49332ad776_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8584A by Chako, on Flickr
The majority of the leads are well labeled. I had to label only 2 plugs which wasn't all that bad. Here is the upgraded SKR Mini E3 v1.2.
<a href="https://flic.kr/p/2jd49Lo" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50019527142_951ea21eee_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8592A by Chako, on Flickr
This board is a huge upgrade over the bare bones Creality board. I will install the BLTouch auto bed leveling kit once I do the needed online video and article readings. At least this upgrade has the proper hookups for it without having to resort to little daughter boards which interfere with the main compartment closing properly.
So after a slow go, I turned on the printer and got this right away.
<a href="https://flic.kr/p/2jcZ7Aq" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50018739388_46f25ed413_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8587A by Chako, on Flickr
I can either go with the classical left, or the touch screen right. I can also press the main knob down for a few seconds to access this screen in either mode.
This is the classical view. A little different from that shown with the original mainboard.
<a href="https://flic.kr/p/2jd49S5" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50019527472_15974bda8f_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8590A by Chako, on Flickr
This is the touch screen interface.
<a href="https://flic.kr/p/2jcZ7t1" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50018738958_10bb6c0d37_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8589A by Chako, on Flickr
I tested both the nozzle and heated bed and everything appears to be working properly.

Next step is to install the auto bed leveling sensor and see how that works. Not sure if I should also flash the board as well. Need to read more I guess. I might also have to do better cable management. I have not installed the cover with the cooling fan on as of yet.
-
Got me some problems. I bought the official Creality BLTouch kit. Apparently, the wire included is different to what is required with the BigTreeTech SKR mini E3 board. Not sure what to do. Got to think about this one more I guess before I proceed any futher.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login


