Skip to content
Collapse
? [[global:guest]]
Unread Recent
HOME SEARCH PROFILE MESSAGES 0 BOOKMARKS MEMBERS BADGES
Multitool.Org Forum
MultiTool.org • Community Header Space • Watch This Space

3D Printer Blog

Scheduled Pinned Locked Moved Gadget Freak and EDC Forum
317 Posts 1 Posters 41.7k Views
  1. Home
  2. Non Tool Forum
  3. Gadget Freak and EDC Forum
  4. 3D Printer Blog
3D Printer Blog
  • Oldest to Newest
  • Newest to Oldest
  • Most Votes
Reply
  • Reply as topic
Log in to reply
This topic has been deleted. Only users with topic management privileges can see it.
  • Chako Offline
    Chako
    Posts: 22,725
    Chako Offline
    Chako
    wrote on last edited by
    #245 Quote Reply

      Time to slowly start this. I plan on finishing tomorrow hopefully. First thing...now that I have a few key upgrades at hand before building the printer, I might be able to do them in a logical sequence that might necessitate less work on my part.

      First thing is first, to install the new stiffer orange bed leveling springs. It is so much easier to flip the bed over without having to worry about the gantry getting in the way. Still a spaghetti mess of wires on the one corner. You can see the upgraded spring in place...and the original one just south of it. These upgraded springs are stiffer and should hold your leveling better compared to the weaker originals.

      <a href="https://flic.kr/p/2jnfY6x" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50123681057_f74a22f70b_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8702A by Chako, on Flickr

      Seeing that I now have the printer on its back...time to start changing the motherboards. I will get this cleaned up and will finish the transfer tomorrow. I ran into a small minor issue. There are 3 screws holding the plate on...however, the bottom plate would not come off. I flipped the printer over on the right side and found another screw that I had to remove...on the Ender 3, there was only the 3 screws. Here is the original motherboard all hooked up.

      <a href="https://flic.kr/p/2jnfXZf" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50123680692_739875c78d_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8703A by Chako, on Flickr

      Much like my Ender 3, they hot glued everything in place. Always a bit of a challenge and fun to remove the hot glue. Here I am starting to remove the cabling on the original motherboard. Yes, both the Ender 3X and the Ender 3 Pro feature the same noisy 8 bit motherboard version 1.1.4. Good thing I will be replacing it with a sweet BigTreeTech SKR Mini E3 V1.2 motherboard.

      <a href="https://flic.kr/p/2jnePQf" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50123458146_832484e93c_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8704A by Chako, on Flickr

      Time to prep the replacement. I have to place the blue heat-sinks onto the stepper controllers.

      <a href="https://flic.kr/p/2jnbVxv" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50122892023_78df905699_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8707A by Chako, on Flickr

      That quick and easy job is done.

      <a href="https://flic.kr/p/2jnePC1" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50123457436_d22bd3610b_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8709A by Chako, on Flickr

      That is it for tonight.

      Merit Badges
      One Piece Collector MTO Tool MP600 Collector Juice Collector Level 3 Japanese PST Charge Collector Sporkman OCD Squad Flashlight Fire Making Scale Changer Photographer Gun User BO Tools Level 3 Time Lord Level 3 Airgun User ALOX Colors Level 3
      1 Reply Last reply
      • Chako Offline
        Chako
        Posts: 22,725
        Chako Offline
        Chako
        wrote on last edited by
        #246 Quote Reply

          Today was a bit fun, and I am not exactly finished yet. I sill need to update the motherboard firmware, and not all went as planned.

          First thing when I woke up was to remove the old board and install the new. Here are both the Creality V1.1.4 board on the left, and the BigTreeTech SKR Mini E3 V3.0 board on the right.

          <a href="https://flic.kr/p/2jnp6Sj" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50125268098_9d024facf8_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8711A by Chako, on Flickr

          I forgot an important step and installed the new board into its compartment.

          <a href="https://flic.kr/p/2jnp6LT" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50125267783_809e26cedd_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8712A by Chako, on Flickr

          Oops. I forgot to install the power leads first as they are mostly impossible to install when the board is screwed down in place.

          <a href="https://flic.kr/p/2jntas6" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50126060597_0622f29854_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8713A by Chako, on Flickr

          Once done, it is a simple manner of screwing down the motherboard and complete the wiring.

          <a href="https://flic.kr/p/2jns38n" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50125840851_6a867d0d85_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8714A by Chako, on Flickr

          Here is the bottom compartment plate. Plenty of ventilation holes compared to the one found on the Ender 3.

          <a href="https://flic.kr/p/2jns35m" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50125840676_20d9aa43de_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8715A by Chako, on Flickr

          Here I am installing the new LCD screen, which I found does not work as advertised. I am uncertain if it is a wiring issue on my part, or the part just shipped damaged. I have 2 white lines running perpendicular, and the whole display is so light I can barely read it. I might have to sent this part back, but I want to play around with it a little more...but not for today. I re-installed the original display and that works great.

          <a href="https://flic.kr/p/2jnp6qc" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50125266583_04c7d04163_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8716A by Chako, on Flickr

          After installing the gantry and the extruder, bowden tube, and nozzle assembly, time to install the few key printed upgrades.

          <a href="https://flic.kr/p/2jntaaT" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50126059657_b5fe8d41fd_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8719A by Chako, on Flickr

          Last to be installed is the Z-Axis bracket.

          <a href="https://flic.kr/p/2jnta6j" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50126059392_e1e7bc52d1_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8720A by Chako, on Flickr

          The completed Ender 3 Pro on the left, and the Ender 3X on the right. I still have a few more things I want to upgrade. I did try the printer after leveling the bed and it works good. I installed the glass plate immediately as it ensures a flatter surface for leveling. Those puck lights I Velcroed to the underside of the gantry have caused problems. Gravity likes to make them fall as the glue fails. I will have to look at another solution that won't endanger a print in progress.

          <a href="https://flic.kr/p/2jns2Mx" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50125839701_ceebba0cc6_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8722A by Chako, on Flickr

          Next steps is to update the firmware, and play around with the BigTreeTech TFT35 E3 LCD. If I cannot figure this out, I may have to ask for another and return this one back.

          Merit Badges
          One Piece Collector MTO Tool MP600 Collector Juice Collector Level 3 Japanese PST Charge Collector Sporkman OCD Squad Flashlight Fire Making Scale Changer Photographer Gun User BO Tools Level 3 Time Lord Level 3 Airgun User ALOX Colors Level 3
          1 Reply Last reply
          • GearedForwards Offline
            GearedForwards
            Posts: 2,720
            GearedForwards Offline
            GearedForwards
            wrote on last edited by
            #247 Quote Reply

              Loving following this thread and seeing your progress and prints!

              What are is the gantry made of? If you're having issues with the lights sticking then magnets may be better if it's a ferrous metal or zip ties if it isn't.

              Merit Badges
              14th Anniversary Anything Goes Challenge Spyderco 30 Day Challenge Minimal SAK Challenge Poker Face Challenge 30 Day Weight-loss Challenge The Batman 30 Day Challenge Titanium Fire Making 30 day challenge - 58, 65 and 74mm SAKs Toothpick User Scale Changer Delemont 30 Day Challenge Paracord Gas Station MRE challenge
              1 Reply Last reply
              • Chako Offline
                Chako
                Posts: 22,725
                Chako Offline
                Chako
                wrote on last edited by Chako
                #248 Quote Reply

                  :tu:

                  Aluminium. Zip ties might be the way. I have noticed however that these LED puck lights eat through 3 AAA cells like nothing. Because of this, I am thinking of something that uses a plug in. As I am typing this up, I remember that I have 2 lights upstairs when I did my leatherwork that are not in use. I may have the solution already. :think:

                  Merit Badges
                  One Piece Collector MTO Tool MP600 Collector Juice Collector Level 3 Japanese PST Charge Collector Sporkman OCD Squad Flashlight Fire Making Scale Changer Photographer Gun User BO Tools Level 3 Time Lord Level 3 Airgun User ALOX Colors Level 3
                  1 Reply Last reply
                  • Dutch_Tooler Offline
                    Dutch_Tooler
                    Posts: 4,434
                    Dutch_Tooler Offline
                    Dutch_Tooler
                    wrote on last edited by
                    #249 Quote Reply

                      Without the writeup and skipping a few of the pics the story might have looked as if the one printer printed the other one :D

                      Nice work! :tu:

                      Merit Badges
                      Carabiner User MTo Store User Hacker Flashlight Mod User Ignore MTO Tool ALOX with Scissors Hook User The Pioneer X Challenge Advanced Modder SOG Power Challenge BO Tools Level 1 Zip Tie User LM Rebar Challenge LM Wave Challenge Victorinox Spirit Challenge Jack'O Lantern Badge SAK STACK Challenge 30 Days The SUPER Challenge MTo Anniversary Challenge Chainsaw User PST 30 Day Challenge
                      1 Reply Last reply
                      • GearedForwards Offline
                        GearedForwards
                        Posts: 2,720
                        GearedForwards Offline
                        GearedForwards
                        wrote on last edited by
                        #250 Quote Reply

                          @Chako said:
                          :tu:

                          Aluminium. Zip ties might be the way. I have noticed however that these LED puck lights eat through 3 AAA cells like nothing. Because of this, I am thinking of something that uses a plug in. As I am typing this up, I remember that I have 2 lights upstairs when I did my leatherwork that are not in use. I may have the solution already. :think:

                          Hopefully that works for you!

                          If not then I'd suggest a USB powered LED strip zippled along the gantry, should be small enough it fits within the gantry's profile and energy efficient :tu:

                          Merit Badges
                          14th Anniversary Anything Goes Challenge Spyderco 30 Day Challenge Minimal SAK Challenge Poker Face Challenge 30 Day Weight-loss Challenge The Batman 30 Day Challenge Titanium Fire Making 30 day challenge - 58, 65 and 74mm SAKs Toothpick User Scale Changer Delemont 30 Day Challenge Paracord Gas Station MRE challenge
                          1 Reply Last reply
                          • Chako Offline
                            Chako
                            Posts: 22,725
                            Chako Offline
                            Chako
                            wrote on last edited by
                            #251 Quote Reply

                              They almost look like twins. :D

                              Lots of options. For example, I am thinking of buying an LED work light for the workbenche. I originally had 3 seperate lights Velcroed and of course they eventually fell. Now I have 6 annoying LED lights held by magnets. Replacing those with a single plugged in light might be the way to go.

                              Merit Badges
                              One Piece Collector MTO Tool MP600 Collector Juice Collector Level 3 Japanese PST Charge Collector Sporkman OCD Squad Flashlight Fire Making Scale Changer Photographer Gun User BO Tools Level 3 Time Lord Level 3 Airgun User ALOX Colors Level 3
                              1 Reply Last reply
                              • Chako Offline
                                Chako
                                Posts: 22,725
                                Chako Offline
                                Chako
                                wrote on last edited by
                                #252 Quote Reply

                                  Well I upgraded the firmware...and had to look up on how to do that again as I only did it the once before. I ended up on Creality's Github website and looked for the same exact firmware file as the other...that being the BLTouch firmware, even though I do not have one currently. I am still playing around with the BLTouch on the Ender 3X...and am not sure if I will spend the 100 bucks to get one for the Pro. Either way, I wanted both machines to be the same to eliminate any complications. I found the required file and renamed it "Firmware.bin". After that, it was a simple matter of copying the file to the micro SD card, and rebooting the printer with the card in the printer. 30 seconds later the firmware was successfully updated.

                                  Here is the printer info on the Pro with the original LCD. Note that there is no mention of the screen being in simulation mode...and it is not a touch screen.

                                  <a href="https://flic.kr/p/2jnJTgb" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50129127932_6c0a7bfc86_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8725A by Chako, on Flickr

                                  Here is the older Ender 3X printer info screen.

                                  <a href="https://flic.kr/p/2jnEQCK" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50128338643_b596cc80ed_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8729A by Chako, on Flickr

                                  Both are now running Marlin 2.0.5.3.

                                  A quick look into the settings on the Pro showed a Z-Axis change of -1.85. This caused me issues with the 3X as it caused my nozzle to move upwards from where I had leveled it manually. This meant the molten plastic was dropping onto the surface and would not stick to the bed. I ended up re-leveling everything and moving that Z-Axis adjustment to 0. Seeing that I have already leveled this one...I will change this back to 0 as well. Anyhow, the BLTouch is not activated in the new Pro just in case I figure out my way around all of this bed leveling and get another for the newer printer.

                                  Just went to the Marlin firmware page and noted they are now at version 2.0.5.4.

                                  Redirecting…

                                  favicon

                                  (marlinfw.org)

                                  Merit Badges
                                  One Piece Collector MTO Tool MP600 Collector Juice Collector Level 3 Japanese PST Charge Collector Sporkman OCD Squad Flashlight Fire Making Scale Changer Photographer Gun User BO Tools Level 3 Time Lord Level 3 Airgun User ALOX Colors Level 3
                                  1 Reply Last reply
                                  • Chako Offline
                                    Chako
                                    Posts: 22,725
                                    Chako Offline
                                    Chako
                                    wrote on last edited by
                                    #253 Quote Reply

                                      Well bad news about the LCD upgrade. I couldn't get it to work properly. The display is so faded that I can hardly see the information on it. Furthermore, there are two bold white thick lines that run parallel across the center of the screen. When I touch the touchscreen, I get a shimmer like you are pressing hard on a regular LCD. Me thinks it is broken. I will mail it back to Amazon tomorrow. :(

                                      Merit Badges
                                      One Piece Collector MTO Tool MP600 Collector Juice Collector Level 3 Japanese PST Charge Collector Sporkman OCD Squad Flashlight Fire Making Scale Changer Photographer Gun User BO Tools Level 3 Time Lord Level 3 Airgun User ALOX Colors Level 3
                                      1 Reply Last reply
                                      • Chako Offline
                                        Chako
                                        Posts: 22,725
                                        Chako Offline
                                        Chako
                                        wrote on last edited by Chako
                                        #254 Quote Reply

                                          Here is the biggest issue with having the motherboard compartment oriented upside down in the Ender 3 Pro compared to the top down compartment of the Ender 3...having to put the printer on its side to do any work inside that compartment. Mind you, how many times will you have to play in there realistically...not much of a complaint in the end.

                                          Here I am getting ready to unhook the serial cable in order to return the BigTreeTech LCD35 E3 V3.0 back to Amazon.

                                          <a href="https://flic.kr/p/2jo8H1a" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50133580997_351b4abf48_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8730A by Chako, on Flickr

                                          Yesterday, I pondered on a better lighting solution for my worktable. I was kidding myself with these little portable battery operated LED lights. They are strong but you can see the lighting dim as you go. The little puck lights worked great, but they ate 3 AAA batteries a day. I visited the local Tractor Supply Company (TSC) and found the perfect solution, a 36" 33W shop light that pumps out 3300 lumen. Operates via a pull chain. Now I have plenty of lasting light, and the best part, no more annoying Velcro or magnets. This one is held in place via 2 screws. :woohoo:

                                          You can see the 3 puck lights removed from the Ender 3X on the lower left. I had 6 magnetic LED lights I bought at the Dollar Store seen on the right and back. problem is, although they stayed up there due to the magnets, each light had a dimmer switch to vary the amount of lighting. They moved when I twisted the knob...and they once again ate batteries.

                                          <a href="https://flic.kr/p/2jo7xwB" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50133354011_d3b77e38e9_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8731A by Chako, on Flickr

                                          <a href="https://flic.kr/p/2jo7xr6" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50133353691_700bc1911b_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8732A by Chako, on Flickr

                                          Merit Badges
                                          One Piece Collector MTO Tool MP600 Collector Juice Collector Level 3 Japanese PST Charge Collector Sporkman OCD Squad Flashlight Fire Making Scale Changer Photographer Gun User BO Tools Level 3 Time Lord Level 3 Airgun User ALOX Colors Level 3
                                          1 Reply Last reply
                                          • Chako Offline
                                            Chako
                                            Posts: 22,725
                                            Chako Offline
                                            Chako
                                            wrote on last edited by
                                            #255 Quote Reply

                                              I am told by Canada Post that my 10 new 608ZZ bearings should be gracing my doors later today. Not sure if that will be the case...but it was time to print another upgrade, and probably one of the better improvements to the Ender 3, the upgraded spool holder for the Ender 3 Pro. This time around, I will be printing 2 sets of bearing holders...one will be 7.8 diameter (original), and a slightly smaller 7 diameter rod. The last time, I had to shrink the rods a bit for them to fit the bearings. I just hope I have enough red PLA left to make this 7 hour print. Time will tell l guess.

                                              <a href="https://flic.kr/p/2joohNB" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50136426271_ab005d0ae8_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8738A by Chako, on Flickr

                                              <a href="https://flic.kr/p/2joohJ8" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50136426011_797b4d1d21_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8740A by Chako, on Flickr

                                              Merit Badges
                                              One Piece Collector MTO Tool MP600 Collector Juice Collector Level 3 Japanese PST Charge Collector Sporkman OCD Squad Flashlight Fire Making Scale Changer Photographer Gun User BO Tools Level 3 Time Lord Level 3 Airgun User ALOX Colors Level 3
                                              1 Reply Last reply
                                              • Chako Offline
                                                Chako
                                                Posts: 22,725
                                                Chako Offline
                                                Chako
                                                wrote on last edited by
                                                #256 Quote Reply

                                                  The new workbench light is strong enough to light the whole room. I am very happy with this 40 dollar purchase...big time.

                                                  Merit Badges
                                                  One Piece Collector MTO Tool MP600 Collector Juice Collector Level 3 Japanese PST Charge Collector Sporkman OCD Squad Flashlight Fire Making Scale Changer Photographer Gun User BO Tools Level 3 Time Lord Level 3 Airgun User ALOX Colors Level 3
                                                  1 Reply Last reply
                                                  • Chako Offline
                                                    Chako
                                                    Posts: 22,725
                                                    Chako Offline
                                                    Chako
                                                    wrote on last edited by
                                                    #257 Quote Reply

                                                      First print with the Ender 3 Pro is happening this morning. I am printing a WW2 Priest 1/100 scale model in black PLA. Nice to have 2 printers chugging away in silence. I still think upgrading the motherboard to this 32 bit silent SKR Mini E3 is the most bang for your buck upgrade. I am still not sure if I will buy another LCD upgrade seeing that the first did not work properly. Cool to see them both running though. Having 2 machines will give me a bit of flexibility.

                                                      <a href="https://flic.kr/p/2jomigG" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50136037618_6a7f013593_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8741A by Chako, on Flickr

                                                      <a href="https://flic.kr/p/2jomibX" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50136037343_6ae8c39331_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8742A by Chako, on Flickr

                                                      Merit Badges
                                                      One Piece Collector MTO Tool MP600 Collector Juice Collector Level 3 Japanese PST Charge Collector Sporkman OCD Squad Flashlight Fire Making Scale Changer Photographer Gun User BO Tools Level 3 Time Lord Level 3 Airgun User ALOX Colors Level 3
                                                      1 Reply Last reply
                                                      • Chako Offline
                                                        Chako
                                                        Posts: 22,725
                                                        Chako Offline
                                                        Chako
                                                        wrote on last edited by
                                                        #258 Quote Reply

                                                          Anyone with more experience know what happened here? I have never encountered this kind of a fail. The only thing I can think of was some sort of slicing error. There bottom layer got laid down and then there was a shift to the right. :think:

                                                          This was on the new Pro. This means I will have to try another print to see if the same issue arises.

                                                          <a href="https://flic.kr/p/2jou8JU" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50137566452_c3bcc32d32_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8743A by Chako, on Flickr]

                                                          The Ender 3X print is going well.

                                                          <a href="https://flic.kr/p/2josVjQ" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50137329576_fe0e18148c_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8744A by Chako, on Flickr

                                                          Merit Badges
                                                          One Piece Collector MTO Tool MP600 Collector Juice Collector Level 3 Japanese PST Charge Collector Sporkman OCD Squad Flashlight Fire Making Scale Changer Photographer Gun User BO Tools Level 3 Time Lord Level 3 Airgun User ALOX Colors Level 3
                                                          1 Reply Last reply
                                                          • Dutch_Tooler Offline
                                                            Dutch_Tooler
                                                            Posts: 4,434
                                                            Dutch_Tooler Offline
                                                            Dutch_Tooler
                                                            wrote on last edited by
                                                            #259 Quote Reply

                                                              Bummer Chako, that Priest was otherwise going to be rather nice...
                                                              Slicing error is what comes to mind as a possible cause, or else maybe a reset of the offset value for that axis at some point. Was the print stopped and resumed at any stage?

                                                              Merit Badges
                                                              Carabiner User MTo Store User Hacker Flashlight Mod User Ignore MTO Tool ALOX with Scissors Hook User The Pioneer X Challenge Advanced Modder SOG Power Challenge BO Tools Level 1 Zip Tie User LM Rebar Challenge LM Wave Challenge Victorinox Spirit Challenge Jack'O Lantern Badge SAK STACK Challenge 30 Days The SUPER Challenge MTo Anniversary Challenge Chainsaw User PST 30 Day Challenge
                                                              1 Reply Last reply
                                                              • Chako Offline
                                                                Chako
                                                                Posts: 22,725
                                                                Chako Offline
                                                                Chako
                                                                wrote on last edited by
                                                                #260 Quote Reply

                                                                  No. No power outage or anything that would cause it to do that.

                                                                  I am printing a very simple gecko right now to see what is what.

                                                                  Merit Badges
                                                                  One Piece Collector MTO Tool MP600 Collector Juice Collector Level 3 Japanese PST Charge Collector Sporkman OCD Squad Flashlight Fire Making Scale Changer Photographer Gun User BO Tools Level 3 Time Lord Level 3 Airgun User ALOX Colors Level 3
                                                                  1 Reply Last reply
                                                                  • Chako Offline
                                                                    Chako
                                                                    Posts: 22,725
                                                                    Chako Offline
                                                                    Chako
                                                                    wrote on last edited by Chako
                                                                    #261 Quote Reply

                                                                      The Gecko made it to completion. Nothing like the first print. I take it something went wrong with the slicer and or the model itself had issues before slicing it. :think:

                                                                      I have noticed something else. The glass plate sticks to the magnetic under-layer something fierce. I wonder how big of a job it is to remove that layer from the aluminium heated plate. :think:

                                                                      Merit Badges
                                                                      One Piece Collector MTO Tool MP600 Collector Juice Collector Level 3 Japanese PST Charge Collector Sporkman OCD Squad Flashlight Fire Making Scale Changer Photographer Gun User BO Tools Level 3 Time Lord Level 3 Airgun User ALOX Colors Level 3
                                                                      1 Reply Last reply
                                                                      • Chako Offline
                                                                        Chako
                                                                        Posts: 22,725
                                                                        Chako Offline
                                                                        Chako
                                                                        wrote on last edited by
                                                                        #262 Quote Reply

                                                                          I received all the other upgrades in the mail today.

                                                                          I received a package of 10 608ZZ bearings...so now the upgraded filament spool now has its ball bearings in place.

                                                                          I received the Y-axis tightener and installed that piece. Once again no included manual...so I had to look at a photo online to figure this out. I like how I can easily make adjustments via a screw knob. Much better than the one included with the PRO...which was nothing actually. Taking off the Pro Y-axis end-cap was a little harder than I anticipated. I found out that the piece is held there via 4 bolts. What I didn't know, was that each bolt was screwed into a hole in the 4040 Aluminium extrusion piece, and not adjustable via those lock nuts that twist in the extrusion channels to lock everything in. So in essence, the Pro did not come with a method to adjust the Y-axis belt. The Ender 3 is adjustable via those channel lock nuts. need to tighten the belt, undo those 4 bolts, pull the whole assembly till the belt is tight, and tighten those same bolts. With that now known, this is a very good upgrade to have. Hard to have any adjustments when no way to do said adjustment is given out of the box. In this way, the Ender 3 is superior because at least you can tighten the belt on the Y-axis if needed.

                                                                          <a href="https://flic.kr/p/2joQpks" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50141521156_e0536649b1_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8745A by Chako, on Flickr

                                                                          The all metal extruder kit also came in. Much better than the cheap plastic version these ship with.

                                                                          Here is the all metal kit ready for assembly and installation.

                                                                          <a href="https://flic.kr/p/2joMC89" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50140978838_e5cbe139e9_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8747A by Chako, on Flickr

                                                                          After removing the plastic version, the metal kit is half installed here.

                                                                          <a href="https://flic.kr/p/2joRBRi" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50141758367_59c7796b85_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8748A by Chako, on Flickr

                                                                          Here it is fully installed. Not only are the parts beefed up, so is the locking coupling for the Bowden tube, which is much larger than that found on the plastic version.

                                                                          <a href="https://flic.kr/p/2joMBTg" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50140978033_38e45dc452_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8749A by Chako, on Flickr

                                                                          So that should be it. I am still thinking on if I should buy another LCD upgrade. :think:

                                                                          Merit Badges
                                                                          One Piece Collector MTO Tool MP600 Collector Juice Collector Level 3 Japanese PST Charge Collector Sporkman OCD Squad Flashlight Fire Making Scale Changer Photographer Gun User BO Tools Level 3 Time Lord Level 3 Airgun User ALOX Colors Level 3
                                                                          1 Reply Last reply
                                                                          • Chako Offline
                                                                            Chako
                                                                            Posts: 22,725
                                                                            Chako Offline
                                                                            Chako
                                                                            wrote on last edited by
                                                                            #263 Quote Reply

                                                                              Just pulled the trigger on that LCD upgrade. Hopefully this one will not arrive broken.

                                                                              Merit Badges
                                                                              One Piece Collector MTO Tool MP600 Collector Juice Collector Level 3 Japanese PST Charge Collector Sporkman OCD Squad Flashlight Fire Making Scale Changer Photographer Gun User BO Tools Level 3 Time Lord Level 3 Airgun User ALOX Colors Level 3
                                                                              1 Reply Last reply
                                                                              • Chako Offline
                                                                                Chako
                                                                                Posts: 22,725
                                                                                Chako Offline
                                                                                Chako
                                                                                wrote on last edited by
                                                                                #264 Quote Reply

                                                                                  This morning, I wanted to test each unit against each other just for kicks. I found a neat easy to print gift card Davinci Catapult here...

                                                                                  Just a moment...

                                                                                  favicon

                                                                                  (www.thingiverse.com)

                                                                                  Load it up in Cura and slice and dice the file.

                                                                                  <a href="https://flic.kr/p/2joYkc8" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50143068113_b34532a1f0_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8750A by Chako, on Flickr

                                                                                  I made sure to glue stick the print beds, and then hit the "preheat PLA" option which gets the heated bed to 45 degrees and the nozzle to 180 degrees. While the printer is doing its thing, I also like to hit "auto home" to speed things up a little. Load the files into each printer after waiting that the bed and nozzle are to starting temperature. Press "print" to start the process. I did this for the exact same time on each printer to race them each out of curiosity. Once the printer registers the file, the printer will then ramp up the bed temperature to 60 degrees, and the nozzle will go up to 200. Once those temperatures are reached, the printer will then go into action.

                                                                                  <a href="https://flic.kr/p/2joYk8F" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50143067913_1f58226852_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8751A by Chako, on Flickr

                                                                                  Screen on the Ender 3X.

                                                                                  <a href="https://flic.kr/p/2jp25ju" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50143603416_d5eebb6623_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8752A by Chako, on Flickr

                                                                                  Screen on the Ender Pro.

                                                                                  <a href="https://flic.kr/p/2jp25fX" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50143603211_5b551b9e37_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8753A by Chako, on Flickr

                                                                                  From the get go, the Ender 3X beat out the Pro ever so slightly. I am calling it a tie due to my probably slight delay in inputting the data between machines...it was a very close variance.

                                                                                  <a href="https://flic.kr/p/2joYjXf" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50143067308_822b12eb90_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8755A by Chako, on Flickr

                                                                                  Merit Badges
                                                                                  One Piece Collector MTO Tool MP600 Collector Juice Collector Level 3 Japanese PST Charge Collector Sporkman OCD Squad Flashlight Fire Making Scale Changer Photographer Gun User BO Tools Level 3 Time Lord Level 3 Airgun User ALOX Colors Level 3
                                                                                  1 Reply Last reply

                                                                                  Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                                                                  Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                                                                  With your input, this post could be even better 💗

                                                                                  Register Login

                                                                                  • 1
                                                                                  • 2
                                                                                  • 11
                                                                                  • 12
                                                                                  • 13
                                                                                  • 14
                                                                                  • 15
                                                                                  • 16
                                                                                  1. Home
                                                                                  2. Non Tool Forum
                                                                                  3. Gadget Freak and EDC Forum
                                                                                  4. 3D Printer Blog
                                                                                  Reply
                                                                                  • Reply as topic
                                                                                  Log in to reply
                                                                                  COMMUNITY LINKS
                                                                                  EDC-TV SAKWiki GearFeed SAKSelector
                                                                                  Operational Funds

                                                                                  Help us keep the Unworkable working!

                                                                                  Make A Donation
                                                                                  November Goal: $300.00
                                                                                  Due Date: Nov 30
                                                                                  Total Receipts: $0.00
                                                                                  Below Goal: $300.00
                                                                                  0% funded
                                                                                  • Login

                                                                                  • Don't have an account? Register

                                                                                  • Login or register to search.
                                                                                  • First post
                                                                                    Last post
                                                                                  0