3D Printer Blog
-
Aluminium. Zip ties might be the way. I have noticed however that these LED puck lights eat through 3 AAA cells like nothing. Because of this, I am thinking of something that uses a plug in. As I am typing this up, I remember that I have 2 lights upstairs when I did my leatherwork that are not in use. I may have the solution already.

Hopefully that works for you!
If not then I'd suggest a USB powered LED strip zippled along the gantry, should be small enough it fits within the gantry's profile and energy efficient

-
They almost look like twins. :D
Lots of options. For example, I am thinking of buying an LED work light for the workbenche. I originally had 3 seperate lights Velcroed and of course they eventually fell. Now I have 6 annoying LED lights held by magnets. Replacing those with a single plugged in light might be the way to go.
-
Well I upgraded the firmware...and had to look up on how to do that again as I only did it the once before. I ended up on Creality's Github website and looked for the same exact firmware file as the other...that being the BLTouch firmware, even though I do not have one currently. I am still playing around with the BLTouch on the Ender 3X...and am not sure if I will spend the 100 bucks to get one for the Pro. Either way, I wanted both machines to be the same to eliminate any complications. I found the required file and renamed it "Firmware.bin". After that, it was a simple matter of copying the file to the micro SD card, and rebooting the printer with the card in the printer. 30 seconds later the firmware was successfully updated.
Here is the printer info on the Pro with the original LCD. Note that there is no mention of the screen being in simulation mode...and it is not a touch screen.
<a href="https://flic.kr/p/2jnJTgb" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50129127932_6c0a7bfc86_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8725A by Chako, on Flickr
Here is the older Ender 3X printer info screen.
<a href="https://flic.kr/p/2jnEQCK" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50128338643_b596cc80ed_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8729A by Chako, on Flickr
Both are now running Marlin 2.0.5.3.
A quick look into the settings on the Pro showed a Z-Axis change of -1.85. This caused me issues with the 3X as it caused my nozzle to move upwards from where I had leveled it manually. This meant the molten plastic was dropping onto the surface and would not stick to the bed. I ended up re-leveling everything and moving that Z-Axis adjustment to 0. Seeing that I have already leveled this one...I will change this back to 0 as well. Anyhow, the BLTouch is not activated in the new Pro just in case I figure out my way around all of this bed leveling and get another for the newer printer.
Just went to the Marlin firmware page and noted they are now at version 2.0.5.4.
-
Well bad news about the LCD upgrade. I couldn't get it to work properly. The display is so faded that I can hardly see the information on it. Furthermore, there are two bold white thick lines that run parallel across the center of the screen. When I touch the touchscreen, I get a shimmer like you are pressing hard on a regular LCD. Me thinks it is broken. I will mail it back to Amazon tomorrow. :(
-
Here is the biggest issue with having the motherboard compartment oriented upside down in the Ender 3 Pro compared to the top down compartment of the Ender 3...having to put the printer on its side to do any work inside that compartment. Mind you, how many times will you have to play in there realistically...not much of a complaint in the end.
Here I am getting ready to unhook the serial cable in order to return the BigTreeTech LCD35 E3 V3.0 back to Amazon.
<a href="https://flic.kr/p/2jo8H1a" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50133580997_351b4abf48_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8730A by Chako, on Flickr
Yesterday, I pondered on a better lighting solution for my worktable. I was kidding myself with these little portable battery operated LED lights. They are strong but you can see the lighting dim as you go. The little puck lights worked great, but they ate 3 AAA batteries a day. I visited the local Tractor Supply Company (TSC) and found the perfect solution, a 36" 33W shop light that pumps out 3300 lumen. Operates via a pull chain. Now I have plenty of lasting light, and the best part, no more annoying Velcro or magnets. This one is held in place via 2 screws.

You can see the 3 puck lights removed from the Ender 3X on the lower left. I had 6 magnetic LED lights I bought at the Dollar Store seen on the right and back. problem is, although they stayed up there due to the magnets, each light had a dimmer switch to vary the amount of lighting. They moved when I twisted the knob...and they once again ate batteries.
<a href="https://flic.kr/p/2jo7xwB" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50133354011_d3b77e38e9_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8731A by Chako, on Flickr
<a href="https://flic.kr/p/2jo7xr6" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50133353691_700bc1911b_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8732A by Chako, on Flickr
-
I am told by Canada Post that my 10 new 608ZZ bearings should be gracing my doors later today. Not sure if that will be the case...but it was time to print another upgrade, and probably one of the better improvements to the Ender 3, the upgraded spool holder for the Ender 3 Pro. This time around, I will be printing 2 sets of bearing holders...one will be 7.8 diameter (original), and a slightly smaller 7 diameter rod. The last time, I had to shrink the rods a bit for them to fit the bearings. I just hope I have enough red PLA left to make this 7 hour print. Time will tell l guess.
<a href="https://flic.kr/p/2joohNB" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50136426271_ab005d0ae8_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8738A by Chako, on Flickr
<a href="https://flic.kr/p/2joohJ8" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50136426011_797b4d1d21_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8740A by Chako, on Flickr
-
The new workbench light is strong enough to light the whole room. I am very happy with this 40 dollar purchase...big time.
-
First print with the Ender 3 Pro is happening this morning. I am printing a WW2 Priest 1/100 scale model in black PLA. Nice to have 2 printers chugging away in silence. I still think upgrading the motherboard to this 32 bit silent SKR Mini E3 is the most bang for your buck upgrade. I am still not sure if I will buy another LCD upgrade seeing that the first did not work properly. Cool to see them both running though. Having 2 machines will give me a bit of flexibility.
<a href="https://flic.kr/p/2jomigG" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50136037618_6a7f013593_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8741A by Chako, on Flickr
<a href="https://flic.kr/p/2jomibX" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50136037343_6ae8c39331_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8742A by Chako, on Flickr
-
Anyone with more experience know what happened here? I have never encountered this kind of a fail. The only thing I can think of was some sort of slicing error. There bottom layer got laid down and then there was a shift to the right.

This was on the new Pro. This means I will have to try another print to see if the same issue arises.
<a href="https://flic.kr/p/2jou8JU" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50137566452_c3bcc32d32_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8743A by Chako, on Flickr]
The Ender 3X print is going well.
<a href="https://flic.kr/p/2josVjQ" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50137329576_fe0e18148c_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8744A by Chako, on Flickr
-
Bummer Chako, that Priest was otherwise going to be rather nice...
Slicing error is what comes to mind as a possible cause, or else maybe a reset of the offset value for that axis at some point. Was the print stopped and resumed at any stage? -
No. No power outage or anything that would cause it to do that.
I am printing a very simple gecko right now to see what is what.
-
The Gecko made it to completion. Nothing like the first print. I take it something went wrong with the slicer and or the model itself had issues before slicing it.

I have noticed something else. The glass plate sticks to the magnetic under-layer something fierce. I wonder how big of a job it is to remove that layer from the aluminium heated plate.

-
I received all the other upgrades in the mail today.
I received a package of 10 608ZZ bearings...so now the upgraded filament spool now has its ball bearings in place.
I received the Y-axis tightener and installed that piece. Once again no included manual...so I had to look at a photo online to figure this out. I like how I can easily make adjustments via a screw knob. Much better than the one included with the PRO...which was nothing actually. Taking off the Pro Y-axis end-cap was a little harder than I anticipated. I found out that the piece is held there via 4 bolts. What I didn't know, was that each bolt was screwed into a hole in the 4040 Aluminium extrusion piece, and not adjustable via those lock nuts that twist in the extrusion channels to lock everything in. So in essence, the Pro did not come with a method to adjust the Y-axis belt. The Ender 3 is adjustable via those channel lock nuts. need to tighten the belt, undo those 4 bolts, pull the whole assembly till the belt is tight, and tighten those same bolts. With that now known, this is a very good upgrade to have. Hard to have any adjustments when no way to do said adjustment is given out of the box. In this way, the Ender 3 is superior because at least you can tighten the belt on the Y-axis if needed.
<a href="https://flic.kr/p/2joQpks" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50141521156_e0536649b1_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8745A by Chako, on Flickr
The all metal extruder kit also came in. Much better than the cheap plastic version these ship with.
Here is the all metal kit ready for assembly and installation.
<a href="https://flic.kr/p/2joMC89" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50140978838_e5cbe139e9_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8747A by Chako, on Flickr
After removing the plastic version, the metal kit is half installed here.
<a href="https://flic.kr/p/2joRBRi" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50141758367_59c7796b85_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8748A by Chako, on Flickr
Here it is fully installed. Not only are the parts beefed up, so is the locking coupling for the Bowden tube, which is much larger than that found on the plastic version.
<a href="https://flic.kr/p/2joMBTg" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50140978033_38e45dc452_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8749A by Chako, on Flickr
So that should be it. I am still thinking on if I should buy another LCD upgrade.

-
Just pulled the trigger on that LCD upgrade. Hopefully this one will not arrive broken.
-
This morning, I wanted to test each unit against each other just for kicks. I found a neat easy to print gift card Davinci Catapult here...
Load it up in Cura and slice and dice the file.
<a href="https://flic.kr/p/2joYkc8" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50143068113_b34532a1f0_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8750A by Chako, on Flickr
I made sure to glue stick the print beds, and then hit the "preheat PLA" option which gets the heated bed to 45 degrees and the nozzle to 180 degrees. While the printer is doing its thing, I also like to hit "auto home" to speed things up a little. Load the files into each printer after waiting that the bed and nozzle are to starting temperature. Press "print" to start the process. I did this for the exact same time on each printer to race them each out of curiosity. Once the printer registers the file, the printer will then ramp up the bed temperature to 60 degrees, and the nozzle will go up to 200. Once those temperatures are reached, the printer will then go into action.
<a href="https://flic.kr/p/2joYk8F" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50143067913_1f58226852_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8751A by Chako, on Flickr
Screen on the Ender 3X.
<a href="https://flic.kr/p/2jp25ju" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50143603416_d5eebb6623_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8752A by Chako, on Flickr
Screen on the Ender Pro.
<a href="https://flic.kr/p/2jp25fX" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50143603211_5b551b9e37_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8753A by Chako, on Flickr
From the get go, the Ender 3X beat out the Pro ever so slightly. I am calling it a tie due to my probably slight delay in inputting the data between machines...it was a very close variance.
<a href="https://flic.kr/p/2joYjXf" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50143067308_822b12eb90_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8755A by Chako, on Flickr
-
Yes, both machines with the same motherboard are the same speed.
Ender 3X.
<a href="https://flic.kr/p/2jp6znb" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50144481576_5cca95662c_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8761A by Chako, on Flickr
Ender 3 Pro.
<a href="https://flic.kr/p/2jp3Nm5" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50143939908_83a5e1a087_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8762A by Chako, on Flickr
I have noticed that the Ender 3 Pro tends to lay a rougher first few layers, and there is a bit of stringing evident. Not sure if it is the PLA filament or something else. Not much difference though.
-
All it now needs is some string of a suitable size.
<a href="https://flic.kr/p/2jp75KG" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50144580438_2a83efae80_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8763A by Chako, on Flickr
-
Trebuchet!!! :ahhh
-
Today came another BigTreeTech TFT35 e3 V3.0 LCD screen. It was a quick swap with the original screen, and now it is working. Noticed that the fonts and display was way different to my other machine. I noticed that there was an update for the LCD screen off of BigTreeTech Github website. After reading the instructions carefully, I wiped a micro SD card and downloaded the proper .bin file. Now here is where things got weird. The instructions also stated I should also download the right folder titled "TFT35" which contained two sub folders, one for bmp icons, and another for fonts. I couldn't for the life of me figure out how to simply copy and past these folders to my micro SD card though. I finally figured that I had to create the same folders and manually open each and every freaking bmp icons, download them manually, and drag and drop them into the right folder. Had to do the same for the fonts. That was fun...and I have to wonder why I couldn't simply download the whole folder in one big swoop. 20 minutes later, I was ready to re-boot the printer with the .bin file and folder...and it worked. I now have similar LCD menues on both the PRO and the 3X (which needed this firmware upgrade).
After it did the firmware update, it also downloaded all those bmp icons and fonts.
<a href="https://flic.kr/p/2jqugj6" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50160224917_786871a935_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8785A by Chako, on Flickr
The old interface was blue. The newest update is a lot more colourful.
<a href="https://flic.kr/p/2jqt1f4" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50159979111_d3f8caf99b_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8790A by Chako, on Flickr
Now both are updated to the same LCD specs.
<a href="https://flic.kr/p/2jqt16m" target="_blank" rel="noopener noreferrer"><img src="https://live.staticflickr.com/65535/50159978606_a7afacf1b9_k.jpg" alt="banner" style="max-width: 100%; height: auto;" /></a>IMG_8794A by Chako, on Flickr
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login