EDC Bit Ratchets
-

Anex low profile ratchet
Weight: 57g
Length: 109mm
Head width: 16mm
Head clearance with standard bit: 26mm (adds 1mm)
Teeth count: 16
Minimum swing arc: 22.5°
Bit retention: magnet
In-line driver: no
Bit material: Chromium-Vanadium steel
Handle material: Chromium-Vanadium steel
Price: $18 with bits
Bits: Slotted 6, Phillips 1/2/3, Allen 2.5/3/4/5/6Accessories
The Anex comes with nine stubby bits, and a plastic bit holder with eight positions. The bit holder has a sticker with the bit specifications. Each position has a hole on the bottom, which makes removing bits easy. The bit holder has good bit retention.
Dimensions
The Anex is certainly on the longer side of edc ratchets, at 109mm. It is thin, with a 16mm wide head, and also very flat. At 57 grams, it is about average weight.
Teeth Count
The teeth count is almost the lowest it can be, tying with the Mulwark/Neiko ratchets at only 16 teeth. This means that the Anex has a minimum swing arc of 22.5 degrees to engage a tooth and get a fastener to turn. This is the most demanding when it comes to available clearance.Bit Retention
The Anex has a magnet to hold bits in. This is the first ratchet that has an exposed magnet. The magnet sits almost flush with the back side of the head. It has excellent retention, and this can be increased further, by placing bits on the magnet.Bit compatibility
Double-ended bits are too long to engage in the shallow ratcheting socket. Stubby bits can be removed easily.
Switch action
The switch protrudes through the back of the frame. Spring-loaded of course, it has good retention. No other switch sits this far away from the ratchet head so far. It is cone-shaped and rather small. This limits the chances of it being bumped accidentally and reversing. It is still very easy and intuitive to operate it.Ease of use
This is advertised as a low profile ratchet, and rightly so. It only adds 1mm to a bit's clearance. It also comes with nine stubby bits. It also has a very narrow head, at 16mm. Of course, having only 16 teeth is not doing it any favors. If there is not enough room to swing the tool to engage the next tooth, it will not be able to turn any fasteners.The ratchet gear is oversized and the teeth are exposed, so it can be used as a knurled finger wheel. No need to swing the tool if a fastener is loose. This helps the limits of the 22.5 degree minimum swing arc.
The ratchet is a little longer than the average edc ratchet, which provides a good grip and a decent amount of torque.
The switch is easy to use, and it is not prone to turn accidentally. Bits are easy to remove.
An interesting and so far unique feature is the exposed magnet. Thanks to this, the ratchet can be attached to ferrous surfaces, for quick access. This also allows bits to be temporarily kept on the ratchet, should the user require swapping between bits often. Adding a bit to the back of the ratchet increases the magnet's strength. For bits that have tight fitment and would perhaps remain in the fastener rather than the ratchet, simply placing a bit on the magnet will make the pull stronger and keep the bits in the ratchet. Of course, thanks to the magnet being exposed, the ratchet can be used as a pick-up tool, to promptly gather loose screws etc.

Construction Quality
The Anex is of the sandwich construction. Two metal plates riveted together, holding all the internals. The fit and finish is good and consistent. The satin finish is crisp. The logo and place of manufacture are engraved flawlessly. The rivets are perfectly centered and chamfered. The ratchet gear is expertly machined, with clearly defined teeth. The ratcheting mechanism has possibly the least amount of wobble in the frame, compared to all other ratchets we have seen. All edges are nicely rounded off, with no hot-spots. The tool is very tactile, with the exposed gear, oversized pawl, cone switch, and smooth satin finish.Portability
The Anex ratchet is very narrow and thin. Granted, other ratchets have a much thinner, cylindrical stem. Still, the Anex fits very comfortably in multi-tool pouch side-sleeves and edc pouches. It will sit nicely in a pen slot. Thanks to the exposed magnet, it can also be stored on a ferrous surface, like a fridge, desk, or shelf, and be ready when needed.
Value
At the time of this review, the Anex cost $18. It came with nine stubby bits, and a bit holder. Rather average at first glance, but then again, not all ratchets can be amazing deals. Still, this is a better deal than it would seem.Conclusion
First of all, the Anex does what it says on the box. It is a true low-profile ratchet. The head is narrow and flat, and it comes with nine stubby bits.
Also, the exposed gear works like a finger wheel. This is not advertised, though it probably should be. This helps make quick work of loose fasteners.
The switch is also a different approach. It is a tiny cone, far away from the head. This all but eliminates the chances of it hanging up on something and reversing, and it is arguably the easiest switch to operate so far.The exposed magnet is also not advertised, and it adds a great amount of versatility to the ratchet. Other bits can be stored temporarily on the back. A bit on the back increases the inserted bit's retention. The ratchet can function as a magnetic pick-up tool. It can also be stored on ferrous surfaces for quick access. This little detail, probably accidental, adds functions that no other ratchet can readily emulate so far.
Lastly, the fit and finish are excellent. This shares construction elements with other sandwich ratchets, like the Mulwark ratchet. The difference in quality is obvious. The ratchet mechanism has the least amount of wobble than any other ratchet we have seen. Tolerances are precise. All edges are perfectly rounded for a comfortable grip. The rivets are perfectly peened and polished.
Considering everything it has to offer, the Anex low-profile ratchet is a good investment. It has capabilities other ratchets do not, it is well-made, it comes with a nice, stubby bit set. As far as edc is concerned, this is perfectly acceptable as well. It is thin and narrow, and will compliment your edc toolkit nicely. Recommended.

Pros
-Exposed magnet provides versatility.
-Good stubby bit selection.
-Low profile head.
-Excellent fit and finish.
-Exceptionally designed switch.Cons
-Only 16 teeth.If you liked this ratchet, also check out:
-
-
No worries. I like ratchets.

-
Lidl Parkside HG05938
Weight: ?g
Length: 100mm
Head width: 19mm
Head clearance with standard bit: 33mm
Teeth count: *80 /!*
Minimum swing arc: 4.5° in theory regarding the teeth count... but, no, seriously, the head play is so bad it has like15°
Bit retention: magnet
In-line driver bit socket: no
In-line driver socket bit retention: -
Bit material: Chrome Vanadium steel
Handle material: Chrome Vanadium steel
Price: 8€ with a square socket drive bit and square socket extension
Bits: 19 1/4" bits, 1 square socket drive bit, 7 sockets (6 to 12mm)Accessories
19 1/4" bits,
1 square socket drive bit,
7 sockets (6 to 12mm)Dimensions
Teeth Count
Quite high, but nearly useless thanks to the play in every joints in that ratchet.Bit Retention
Very good retention with the magnet.Bit compatibility
no compatibility with double head bits
Stubby bits can be removed with some persuasion.Switch action
The switch is short but not flat, it has a correct detent and does not want to turn accidentally.Ease of use
No knurled wheel for thumb action.Construction Quality
As good as a 8€tool can be
Horizontal/polar play around the teeth, vertical play on the joints (see pics)Portability
The box could be much smaller/compact, but looks reasonably sturdyValue
8€ is a really fair price for a tool like that : the tool is not of "good quality" as a Wera, Victorinox, or Facom tools can be, but it is "good enough" for time-to-time work.Conclusion
The low price makes it attractive as a disposable tool : don't expect it for either heavy duty use or even regular use. It could very well fit as a tool that you'll use once in a while and can lend to friends without worrying of it being broken : it will eventually break, but no one will bother
Pros
-High teeth count.
-Many accessories
-Cheap
Cons
-Cheap
-Quality as low as the price
-No extension for use with standard hex bits..jpg)
.jpg)
.jpg)
.jpg)
-
Well, for the money, that's a good enough set. I got a ratchet that looks a lot like that one. But mine is fine. Not impressive, but usable.
I've seen a few bit ratchet sets in my local shops, that are not available in Amazon etc. I might just pick up a couple.

-
Thanks to your
enablinggreat reviews I now own way more ratchets than I need. But do you have recommendations for bit storage? All I can find are hard plastic holders which make the bits difficult to retrieve until they wear... and then become too loose. There has to be a better solution (a softer material, a holder with magnets?) but everywhere I look it seems there's only one model available.
-
@ComboTool said:
Thanks to yourenablinggreat reviews I now own way more ratchets than I need. But do you have recommendations for bit storage? All I can find are hard plastic holders which make the bits difficult to retrieve until they wear... and then become too loose. There has to be a better solution (a softer material, a holder with magnets?) but everywhere I look it seems there's only one model available.
I have found a storage method that works perfectly for my edc. I'll take pictures and explain in detail tomorrow.
I have a couple of ratchets -not yet reviewed but close- that have arguably the best bit holders of all. They're next to be reviewed. After the next one.
-

Penggong mini ratchet
Weights
Ratchet: 67g
Extension: 26g
Bits in holder: 75g
Entire kit: 201gLength: 93mm
Head width: 18mm
Head clearance with standard bit: 32mm (adds 7mm)
Teeth count: 60
Minimum swing arc: 6°
Bit retention: magnet
In-line driver: no
Extension bit retention: magnet
Bit material: Chromium-Vanadium steel
Handle material: Chromium-Vanadium steel
Price: $13 with 10 double-ended bits, spring-loaded bit holder, locking bit extension, and carrying case.
Bits:- Allen 2 - Tri-point 1
- Allen 3 - Phillips 2
- Allen 4 - Phillips 1
- Allen 5 - Phillips 0
- Allen 6 - Spanner 6
- Allen 2.5 - Tamper-proof Torx 10
- Triangle 2.3 - Tamper-proof Torx 15
- Slotted 3 - Tamper-proof Torx 20
- Slotted 5 - Tamper-proof Torx 25
- Slotted 6 - Tamper-proof Torx 30
Accessories
The Penggong ratchet comes with 10 double-ended bits, a spring-loaded bit holder cartridge, locking bit extension, and carrying case.The bits are double-ended, but they are the same length as standard bits.
The bit holder has ten slots, each with its own button and bit specifications. Pressing the button releases a bit and exposes one end. There is some rattling but the bits cannot simply fall out. The holder can hold standard bits as well. Stubby bits will sink in too deep and require tools to extract them.
The holder inserts in the carrying case and is held in place with a push-tab.The extension is spring-loaded and locking. The collar has to be pulled back for both inserting and removing bits. This extension is made for standard bits. The double-ended bits the ratchet comes with have their retention notches in the middle. Most of these bits do not engage properly in the extension and do not lock. Standard bits engage and lock properly.
The carrying case has a belt clip that has stops at the horizontal and vertical positions. The ratchet and extension clip into it. The teeth that secure the ratchet and extension are not flexible, and they have developed white spots from stress. The bit holder cartridge inserts into its own pocket, and is held in place by a somewhat flexible tab.

Bottom right: Common double-ended bit, Leatherman bit, standard bit, Penggong bit, SK ratchet stubby bit (18mm), SK ratchet ultra stubby (12mm)Dimensions
This is 93 mm long, which is mid-range. Long enough to provide a good grip and decent torque, and short enough for edc. At 67 grams, this is a bit on the heavy side. The head is 18mm wide, which is excellent.
Teeth Count
The Penggong ratchet has 60 teeth, which means it has a 6 degree minimum swing arc. This is quite high, certainly for a ratchet this inexpensive.Bit Retention
The bits are held in by a magnet. It has good retention and holds on bits firmly.Bit compatibility
The ratchet socket is rather deep, to accommodate the double-ended bits it comes with. Because of this the ratchet is compatible with common double-ended bits that are a little longer than an inch. Regular double-ended bits engage for about 1mm, but can be used. Leatherman bits engage much more and have about as much play as standard one-ended bits.
Stubby bits sink in a little too deep. The tip is exposed and they can be used, but they are difficult to remove.
Switch action
The switch is short and has good detent. It sits in its own scalloped area. As it is somewhat hidden, it is unlikely to get bumped accidentally and have it reverse the action.Ease of use
With 60 teeth, the Penggong has a minimum swing arc of only six degrees. The head is 18mm wide, so this can come in handy for accessing fasteners in crammed locations. The head adds 7 mm to a bit's clearance. Stubby bits could help with this, but they are not easy to remove from the deep ratchet socket.The handle shape is very reminiscent of the Wera Zyklop mini handle. Of course the Penggong lacks the scallops. The neck is longer. The flaring of its handle is also more pronounced. The Penggong is very comfortable to hold. The fingers are guided into a natural grip. Due to the length, this is a three-finger grip.
The ratchet has a knurled finger wheel. This is almost flush with the head. It is not hard to use, but requires a little finger pinching to get it to spin.
The bits are double-ended, but they are the same length as regular 1/4" bits. There are ten bits, so we have twenty drivers. Included are Philips, slotted, six metric Allen ends, five tamper-proof Torx, a triangle, a tri-wing, and a spanner end. Certainly a comprehensive set, that manages to be compact, thank to the bits being double-ended.
The bit holder is a stand-alone piece that can be removed from the holder and carried separately. Every bit has a push button to release it. The holder has bit sizes on the outside, to quickly identify the one needed. This can also hold standard, single-ended bits. Do not place stubby bits in this. They will sink in and removing them will not be easy.
The extension sits on the back of the holder. This adds a few steps to its removal, as the whole case must be removed from the belt in order to access the extension. It is a locking extension which also has a magnet. The collar has to be pulled back for both inserting and removing bits. This works perfectly with standard bits. The ball bearings that engage the retention notches are just the right height. The bits the ratchet came with do not lock in this extension, because the retention notches are at the very middle of the bit length. It is curious that this happens. A simple, deep extension would have been better. The bits can still be used in this extension, and standard bits will lock in it properly, so arguably nothing is lost.

Construction Quality
The case is made of hard plastic. This does not feel high-quality. There are stress marks on the parts that the ratchet and extension clip onto.
The extension is a common locking extension. The finish has a worn look to it.
The bits are crisp. They have a copper-like finish that has remained unaffected by use.
The ratchet's fit and finish are more than acceptable. The satin finish is consistent. Everything is nicely chamfered. The moving parts have good tolerances. The magnet has good bit retention. The switch has good detent and does not reverse the action accidentally. The ratchet has very little wobble in the ratchet head.Portability
The case has a wide belt-clip, with indexing at right angles. The belt clip also has raised ridges to hook on the belt and keep it in place. The case holds everything firmly. It weighs 201 grams, which is quite good for a ratchet set. The ratchet and bit holder can be removed easily with the case on a belt. The extension is held on the back, so to access it and put it back, the whole case may have to be removed from the belt.On its own, the ratchet is short enough to fit in an edc pouch or multi-tool pouch side-sleeves. The hourglass shape helps with retention.

Value
This is the second most inexpensive ratchet so far, costing only $13. The Jackly keychain ratchet cost $9. For its price, the Penggong ratchet has some nice features and it comes in a comprehensive kit.Conclusion
The Penggong ratchet sure is interesting. It has excellent ergonomics, a high teeth count, a knurled finger wheel, and a narrow head. It comes with a locking bit extension, a bit holder cartridge, ten double-ended bits, and a case with a belt-clip. The ratchet is well-made, with a nice satin finish, great tolerances, and a clean, chamfered frame. The extension is locking, which is a nice addition for such an inexpensive kit. The double-ended bits offer an excellent variety of tips, including five Tamper-proof Torx and six metric Allen tips. They are also the same length as standard single-ended bits. The bit holder cartridge can be removed from the case and be carried separately. It can also store standard bits. The case is certainly not impressive, but it does a good job of holding everything. The ratchet and extension clip into place. The bit holder sits in its own pocket.This is reminiscent of the Ovatt ratchet, which also has 60 teeth, comes with ten bits, an extension, and a plastic case with a belt clip. However, the Penggong wins in every category. The ratchet is of better quality and the knurled finger wheel much easier to operate. It costs almost half as much, the bits are double-ended, and the extension locks. The bit holder is removable and much more effective in keeping bits stored when you want them stored, and releasing them when you want them released.
Comparing the Penggong ratchet to others of well-known brands does not seem fair. Obviously the Wera, Wiha, Topeak, etc are going to be superior, be it in quality, durability, features, materials, etc. Still, this only cost $13. The ten double-ended bits in the bit holder cartridge alone could be $13 and it would not be a bad purchase. The locking extension is also worth a few dollars. The ratchet has some nice features and works as intended, and it is also edc-friendly. As far as the kit-to-price ratio, the Penggong ranks rather high.
It is hard not to recommend this. It works for edc, the bit selection is above average, it includes a nifty bit holder and an extension, and it will not break the bank.

Pros
-Ten double-ended bits of standard bit length.
-Versatile bit set (triangle, 6x Allen, 5x tamper-proof Torx, etc).
-Bit holder is separate and removable.
-Inexpensive.
-Good ergonomics.
-High teeth count.Cons
-Double-ended bits work but do not lock in provided extension.
-Head adds 7mm to bit clearance.
-Knurled finger wheel is not the easiest to use.If you liked this ratchet, also check out:
-
@ComboTool said:
Thanks to yourenablinggreat reviews I now own way more ratchets than I need. But do you have recommendations for bit storage? All I can find are hard plastic holders which make the bits difficult to retrieve until they wear... and then become too loose. There has to be a better solution (a softer material, a holder with magnets?) but everywhere I look it seems there's only one model available.This is my solution to carrying a ton of bits.
I carry a cheap trifold wallet. I sewed two elasticated strap loops on it.
One loop holds my edc ratchet (Ares) with a Phillips #2 in the in-line driver.
The other loop holds my Deluxe Tinker in a Roxon knife pouch to keep lint out.
The change pocket holds a slide-top tin, and a bit extension with a #4 Allen bit.
Before the tin, I had the extension and the two Mulwark bit holders.

The tin is this one:
Spoiler:
Mini Skater 4Pcs 3.15"x1.97"x0.59"Mini Metal Slide Top Tin Containers, Sliding Cover Push-Pull Tin Box,Portable Slide Cover Storage Box for Wedding Jewelry Lip Balm Container Cosmetic Organizer(Black)
https://www.amazon.com/dp/B094JG4N1P?psc=1&ref=ppx_yo2ov_dt_b_product_detailsThe tin fits two layers of 1/4" bits.
One layer is 12 standard bits, and 12 stubby bits.
The second layer is another 12 standard bits, a 4mm bit adapter, 10 4mm bits, two stubby bits and the stubby socket adapter that comes with the Klein ratchet, and three 2 dollar coins.This may be overkill, so maybe an Altoids Smalls tin would be better for most people.
%20-%20Copy.jpg)
.jpg)
-
-

LaBear mini ratchet
Weight: 44g
Length: 99mm
Head width: 19mm
Head clearance with standard bit: 30mm (adds 5mm)
Teeth count: 12
Minimum swing arc: 30°
Bit retention: magnet
In-line driver: no
Bit material: S2 steel
Handle material: Chromium-Vanadium steel
Price: $9 with 10 bits (listed as 11 but PH1 missing)
Bits: Phillips 2, Slotted 4 and 6, Torx 15 and 20, Allen 3, 4, 5, 6, 1/4" square adapter (and Phillips #1 bit listed but missing)Accessories
The LaBear comes with nine stubby bits (listing says ten but one bit was missing) and a 1/4" square adapter in a bit holder. The bits are very difficult to remove from the holder.Also included is a plastic finger spinner that attaches to the ratcheting bit socket. The spinner's opening is quite a tight fit for bits, and it obstructs view of the bit socket, so it is not possible to align the bit properly and insert it. To change a bit, the bit has to be removed, then the spinner has to be removed, then a new bit is inserted, then the spinner again. Quite a lengthy process if working with multiple drivers.
The spinner is 20mm wide, so adding this to the ratchet increases the head width.
Dimensions
The LaBear ultra low-profile ratchet seems to be misnamed. With no bit inserted the head is 15mm tall. The ratchet adds 5mm to a bit's clearance.
The head is 19mm wide, not the widest, not the narrowest.
It is 99mm long, which is respectable, and means the LaBear will fit comfortably in any garbage bin.
Teeth Count
The teeth count is abysmal, at only twelve, which means that this has a minimum swing arc of thirty degrees. It does not get worse than this.Bit Retention
The bits are held in place by a magnet. It is very strong, making bits with thin tips hard to extract.Bit compatibility
Double-ended bits cannot be used in this. Stubby bits with thin tips are hard to remove.
Switch action
The LaBear ratchet has an oversized spring-loaded pawl which acts as its own switch. It has very poor detent and switches sides with the slightest touch.Ease of use
Even though it is advertised as an ultra low profile ratchet, this has quite a tall head. The bit socket protrudes quite significantly. The head adds 5mm to an inserted bit's clearance, which is barely low profile, let alone ultra low profile.
The ratchet has only twelve teeth, so it will need more space than any other ratchet to be able to engage the next tooth and turn a fastener.
A finger spinner is included, which helps with somewhat loose fasteners. This attaches to the driving socket quite firmly, and also increases the bit retention. It also makes it hard to remove bits, and time-consuming to change bits around, as the spinner has to be removed and re-inserted along with the bits.
The action can be reversed accidentally, due to the pawl's poor detent.The exposed magnet adds some versatility. The tool can attach to ferrous surfaces, and also act as a short magnetic pick-up tool.
The bits are difficult to remove from the bit holder. Some bits are very tight, and others require additional tools to aid extraction.

Construction Quality
The magnet was barely pressed in the socket. The product listing shows the magnet being flush with the back-plate.
The two halves of the frame leave gaps, as they are misaligned and do not sit flush against each other. There are burrs and imperfections along the edges.
The rivets are not properly chamfered and will grab fabric.
The ratcheting mechanism feels weak. The gear turns very easily, with very little resistance. The ratcheting clicks are anemic. The whole mechanism feels loose and janky.Portability
The ratchet has a flat frame and is not overly wide. It fits in multi-tool pouch side-sleeves and edc pouches. The (extremely) exposed magnet allows the tool to be stored on a ferrous surface. Of course it will take very little space in any recycling bin or garbage can, and is heavy enough to be tossed into a lake or river.
Value
At only $9, this is the least expensive ratchet so far. No surprises there. It is quite obvious that several corners were cut to achieve this.Conclusion
This costs only $9 and it shows. The ratchet is functional, although that is a given. The bit set would arguably be worth the asking price. The bits are S2 steel, and there is also a 1/4" square adapter included. Alas, a bit was missing, and this seems to be the norm with this ratchet.The ratchet has the fewer teeth so far, at a mere dozen. It also has a decisively not ultra low profile head. The action is weak, and can be reversed easily by accident. As if these were not enough, the ratchet is riddled with flaws. The magnet was barely pressed in. The frame has gaps and imperfections. The rivets are rough and will catch on skin and fabric.
This is a new low. There is no way around this and no reason to recommend it. There are much better options for a few dollars more.
Pros
-Exposed magnet adds versatility.
-S2 stubby bits.Cons
-Arriving with missing bit is common occurrence.
-Only 12 teeth.
-Head is 15mm tall with no bit.
-Head adds 5mm to bit clearance.
-Poor build quality.
-Bits are extremely tight in holder.
-Spinner increases head width and makes changing bits tiresome.If you liked this ratchet, read this review again and pay attention this time. Also check out:
-
-
I used a Knipex pliers wrench to press the LaBear's magnet in the socket.

Before:

After:

-
@m47mu74nt said:
Looks like 8€ Lidl one is far better than that one!
(Btw, I've just ordered Facom R1-pico in the yellow cycling limited edition variant, just because it was yellow and ... A limited edition.
)I'd take the Lidl one over the LBear any day of the week.
And that yellow box looks great. That's a fantastic shade of yellow.

-
Lots of great in depth reviewing, RP
:ahhh

-
Thanks!

-
I keep seeing tools in Amazon that are out of stock...

Something's up. :ahhh -
-

Vessel low-profile ratchet
(can also be found branded by Broppe and Lattook)
Weight with no bits: 48g
Weight with 2 bits: 54g
Length: 104mm
Head width: 16mm
Head clearance with standard bit: 25mm (adds 0mm)
Teeth count: 16
Minimum swing arc: 22.5°
Bit retention: spring
In-line driver: no
Bit material: Chromium-Vanadium steel
Handle material: Chromium-Vanadium steel
Price: $16 with 11 stubby bits
Bits: Allen 2/3/4/5/6, Phillips 1, 2 x2, 3, Slotted 4 and 6Accessories
The Vessel low-profile ratchet comes with eleven stubby bits and a bit holder. The bits are the shortest stubby bits yet, at only 18mm long (the SK ratchet comes with three half-cut bits, that are 12mm long).
The bit holder is modular. It consists of three connecting pieces. When connected, the pieces have an insignificant amount of wobble and stay together with no issues.
Bottom right, left to right: SK ultra stubby (12mm long), Vessel stubby (18mm long), SK Anex Klein stubbies (19mm long), LaBear Mulwark (20mm long)Dimensions
The Vessel ratchet is 104mm long, which is a little above average. The head is 16mm wide, which is great. The head adds no length to a bit's clearance.
At 54g with two bits in the handle, it is about average weight, perfectly acceptable.
Teeth Count
With only 16 teeth, this requires some space in order to engage the next tooth and turn a fastener.Bit Retention
Bits are held in by a spring. This is not excessively tight and offers good retention.Bit compatibility
Stubby bits can be removed easily.
Double-ended bits work well in this thanks to the hole in the back of the head.
Switch action
The Vessel has a spring-loaded, oversized pawl, which is its own switch. The pawl protrudes from both sides of the frame at all times. To reverse the action, a tip must be pushed up or down. It has good detent and it is not easy to get it to reverse accidentally.Ease of use
The Vessel is the only ratchet so far to feature on-board bit storage. It has two bit slots built into the frame. The bits are secured by two rows of ridges in the hard plastic insert. The bits clip into their spots and are very secure. To remove a bit, simply push it out from the other side. The Vessel stubby bits are 18mm long, but the ratchet can store 19mm long stubby bits. 20mm long stubby bits will not fit, and of course, standard bits will not fit in this.
The ratchet gear is oversized and the teeth are exposed, so this can be used as a knurled finger wheel to quickly turn loose fasteners.
The ratchet head is 10mm tall and adds no length to an inserted bit's clearance. As long as there is room to swing this, it will reach into some crammed spots.
The sides have some jimping that provides some additional traction. The ratchet is long enough for a four-finger grip. Reversing the action is very easy.
Top right from left to right: LaBear, Anex, Vessel, Mulwark, SKConstruction Quality
The finish is crisp and consistent. The pawl and gear engage smoothly. Tolerances are great. There are no gaps between the plates and hard plastic insert. The lanyard hole edges are chamfered and will not wear down cords. The rivets are smooth and will not grab fabric. The Vessel logo is etched flawlessly on the frame. The bits fit in the frame perfectly, clipping in place with an audible click. The ratchet mechanism has very little wobble in the frame.
The sides of the plates appear slightly unfinished, but they are very smooth to the touch.The bit holder is wonderful, with no molding imperfections. The pieces connect to each other convincingly, with very little wobble. Bits are held firmly, but are not overly tight.
Portability
The Vessel ratchet is straight and flat, and sits comfortably in multi-tool pouch side-sleeves, edc pouches, and pen sleeves.
It also has a 4mm lanyard hole, and the bit holder has a loop too, so these can be carried with carabiners or clips, and attached to other gear.
Value
The Vessel ratchet cost $16, and came with eleven stubby bits and a bit holder. The ratchet has some nice features, the bits are 18mm long, and the bit holder is modular.Conclusion
Having 16 teeth is a little low. This will need some space to swing around in order to work. This is a common occurrence with ratchets of the sandwich design. Still, the Vessel has some tricks up its sleeve.Compared to its kin, the Vessel has quite a few features. Jimping for traction, a knurled finger wheel, a lanyard hole, and of course, on-board bit storage. It is also flat, adds no length to the bit clearance, and comes with a modular bit holder and eleven 18mm long bits. It certainly has a lot to offer.
Its features translate well into edc. The ratchet fits nicely in pouches, it has a lanyard hole so it can be tethered or clipped on other gear. The bit holder also has a loop and has a few carry options, depending on the number of bits users want to carry. The ratchet can store two bits within its frame, and it is compatible with double-ended bits as well. The hard plastic insert is a vibrant, highly visible orange, and it even has some jimping for traction. The Vessel low profile ratchet is a solid choice for a compact, edc bit ratchet.
Pros
-Knurled finger wheel.
-On-board bit storage.
-Ratchet adds no length to bit clearance.
-Modular bit holder.
-Shortest stubby bits yet (18mm long).Cons
-Only 16 teeth.
-The ratchet cannot store standard bits.If you liked this ratchet, also check out:
-
Great review RP, I was actually looking at a few of those yesterday.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login
















































