EDC Bit Ratchets
-
LaBear Mini Folding Ratchet
(Can also be found branded by ASA, Astro, B Baosity, Calandis, Chain, Laser, Leefasy, Mycense, Startist)
Weight: 48g
Set weight: 78g
Length folded: 47mm
Length unfolded: 78mm
Head width: 18mm
Head clearance with standard bit: 28mm (adds 3mm)
Teeth count: 72
Minimum swing arc: 5°
Bit retention: magnet
In-line driver: No
Bit material: Chrome Vanadium steel
Handle material: Chrome Vanadium steel
Price: $16 with 5 bits, bit holder, split ring with tiny chain.
Bits: Allen 4, 5, 6, Torx 25, 30Accessories
The LaBear Mini Folding Ratchet comes with five standard 1/4" bits, a bit holder with 5 bit positions, and a split ring with a tiny chain attached to the end.The bit holder attaches magnetically to the back of the ratchet handle. It also seems to be a friction fit and it feels secure. The bits are held in by friction, with protruding rings of plastic engaging the bit retention notches. The bits have some wobble in the holder, but require some force to be removed, so retention feels adequate.
The bits are Chrome-Vanadium, and the coating has held up to some use. There are three common size Allen bits, and two Torx bits, so this will require some replacements to function as an edc ratchet.
Dimensions
At 78 grams for the ratchet, and five bits in the piggy-back holder, this seems quite good. The bit holder can be removed, should the entire kit feel heavy for a keychain. The ratchet alone is 48 grams, which is much more tolerable on a keychain. It is 47mm when folded, so it really tucks into a small package. The head is 18 mm wide and for 72 teeth, that is just excellent.
Bottom right: LaBear Folding, 711L, Jackly, Leatherman, Ares, Wera, Tone, Wiha, Sharden, Bosch, Topeak, Blackburn, Zoyo, Victorinox, CyclingDeal, PrestaCycle
Teeth Count
At 72 teeth, this has a minimum arc of only 5 degrees. This is almost as good as it gets, and certainly the highest so far for a ratchet this small.Bit Retention
Bits are held in place with a magnet. Retention is firm, so in theory, you could keep an additional bit in the ratchet, since the holder only holds five.Bit compatibility
Stubby bits can be removed easily thanks to the socket being shallower than more ratchets.
Of course, being this shallow, double-ended bits and Leatherman bits cannot be used.
Switch action
This ratchet has the same head as the Wiha and CyclingDeal ratchets, with one notable difference: The switch has been switched to a regular, small switch, similar to those of the PrestaCycle, Topeak, Wera, etc ratchets. This is a nice change. The Wiha and CyclingDeal ratchet switches were quite oversized. This switch is still easy to use, but is tucked away nicely behind the knurled wheel, and does not protrude at all. The detent is great, so it will not change directions accidentally.
LaBear, Wiha, CyclingDealEase of use
The first so far, this is a folding ratchet. As this is a button lock, the ratchet head is locked both in the opened and closed positions.
Opening and closing the ratchet is very easy, but it is a little too tight, so this cannot be flicked open like a button-lock knife.
The ratchet head has some play in both positions. It locks firmly when opened. When folded, the magnet that holds the bit holder also keeps the ratchet head against the handle, in addition to it being locked closed as well.The ratchet can be used folded for a quick fix. When unfolded, it is a three-finger grip, although the pinky also holds onto it thanks to the chain. There is a knurled wheel for somewhat loose screws. The switch is easy to operate. The head has 72 teeth, so this only requires a clearance of 5 degrees to be able to swing and turn a fastener.
The bit holder attached with a 1/4" peg into the handle's 1/4" hex hole, so bits fit in the back of the handle perfectly, but this is not to be treated as a bit driver. The sidewalls are plastic, and it will not handle much torque. Also should the plastic become warped, the bit holder will lose the friction fit and only be held in by the magnet.
The split ring allows this to be attached to keys or other gear, although a clip or carabiner will have to be used for easy removal. Adding a clip or carabiner will increase the length of this, so maybe replace the split ring with a carabiner altogether.
Of course, this is a folding ratchet, so it should be used lightly. It will not handle the abuse other ratchet will, because of the nature of the folding construction.

Construction Quality
The LaBear folding ratchet is a far cry from the LaBear flat ratchet, in a good way. This is a good quality ratchet. The finish is consistent. There are no gaps between scales and spacer. The screws look new and crisp. The ratchet head mirror finish is flawless. The bits are finished nicely and fit their respective fasteners perfectly, and the coating holds up to use. The bit holder holds the bits securely and itself attaches firmly onto the frame.One small issue was that the first chain link that attaches to the ratchet end was not perfectly circular. It had been jammed in place instead of being properly threaded through the hole and being able to rotate freely. It would be recommended to replace this for a split ring, that will hold up to more force than a simple crimped chain link.
Portability
Arguably its selling point, portability seemed to be the idea behind this. The ratchet folds in two, making it shorter and easier to have on a keychain. It comes with its own keychain set-up and the bit holder also attaches on it, so users can have a few bits quick on hand.
It would make little sense to have this unfolded to fit in an edc pouch. It certainly can be done, but at the same time, why go that route instead of having a longer, sturdier ratchet in the pouch to begin with? This was designed for attaching to keys or other gear, so stuffing it into a pouch may be inelegant and inefficient.
Value
At $16, this is a fine value for money. The head alone would be worth it, as it has 72 teeth and a knurled wheel, features we do not commonly see on ratchets this inexpensive.Conclusion
The LaBear folding ratchet was a breath of fresh air, considering the atrocious LaBear flat ratchet. The folding ratchet is well-made, has features of much more expensive ratchets, comes with a nifty bit holder and five bits, and it also folds in two. Definitely an interesting design, and well-suited for edc, which this thread is investigating. The ratchet also comes in a variety of colours, like most edc gadgets. And it is inexpensive and readily available, at least at the time of this review.A few kinks still have to be ironed out, but this is indeed a good option for edc. It works as intended, it is well-made, it is a nice little conversation piece, and it will also make a neat stocking stuffer even for people who are not all that into edc. Recommended.

Pros
-72 teeth.
-True edc set-up
-Available in multiple colours.
-Inexpensive.Cons
-Lighter use than fixed-handle ratchets.
-Split-ring should be clip.
-Chain link should be eyelet screw/split ring.If you liked this ratchet, also check out:
I have another brand to add to this one- I just got a Ko Konjojo branded one.
/topic/93938
Def
-
I quite like mine. It is a nice little tool.

-
Rujoi Flex-head bit ratchet
Weights
Ratchet: 69g
Extension: 33g
Set: 265gLength: 128mm (The Amazon listing says it is 100mm long. It is not. The seller reassured me it will be corrected).
Head width: 18mm
Head clearance with standard bit: 27mm (adds 2mm)
Teeth count: 60
Minimum swing arc: 6°
Bit retention: spring detent
In-line driver retention: magnet
Extension bit retention: magnet
Bit material: S2 steel
Handle material: Chrome Vanadium steel
Price: 40$ with 12 bits, 1/4" square adapter, 3 sockets, extension, and case
Bits: Phillips 2, Torx 10/20/25/30, Allen 2/2.5/3/4/5/6/8, 1/4" square adapter
Sockets: 8mm, 9mm, 10mm
Flex-head positions: 15° incrementsAccessories
The Rujoi Flex-head ratchet comes with twelve S2 steel bits, a square adapter for sockets, three sockets, a long extension, and a hard nylon case.
The case is clam-shell with a zipper. One side has a foam insert, which has cut-outs for the ratchet, bits, sockets, and socket adapter. The other side has a mesh pocket that houses the extension. The pocket runs about half the length of the case.
Dimensions
At 128mm, this is the longest ratchet yet. It may not fit a small edc pouch. This exact head can be found on shorter ratchets. The head is 18mm, which is narrow enough. The head adds 2mm to an inserted bit's clearance. Quite good.
Teeth Count
The ratchet has 60 teeth. This is on the higher side, and it means the ratchet has a minimum swing arc of only six degrees to engage the next tooth.Bit Retention
The ratchet head has a retention spring, which is the same spring found on other high quality ratchets, like the Topeak, Prestacycle, Wera, etc.
The in-line driver has a magnet of above average strength.Bit compatibility
The ratchet is a nigh-pass-through design, so it works with most double-ended bits. For Leatherman bits, the spring has to engage their retention notches, so the bits do not fall out. Stubby bits are easy to remove, thanks to the hole in the back of the ratchet head. Bits can be pushed out enough for them to disengage the spring.
The in-line driver and extension driver are too shallow for double-ended bits. Leatherman bits engage but barely, and have too much flop from side to side to be used effectively. Stubby bits do not sink in but they are not particularly easy to remove.
Switch action
The switch is short and flat. It rests on a completely flat surface and has excellent detent. It does not get in the way of the flex-head pivot or the knurled wheel.As it is a locking flex-head ratchet, there is also a button. It protrudes 2mm from the frame and is spring-loaded. It is in the shape of a flat mushroom and sinks completely into the frame,with no grinding or jamming.
Ease of use
As a flex-head ratchet, the Rujoi offers a clear advantage compared to fixed head ratchets. The flex-head is locking and moves in 15° increments. Thank to the various positions of the head, this ratchet can access fasteners in confined spaces that fixed head ratchets could not.This ratchet happens to share its head with the Prestacycle T-handle ratchet. As such, the Rujoi can also accept the extension as a T-handle, and provide additional torque to the in-line driver.
As this is 128mm, users with large hands may find it easier to hold and use, compared to other much shorter ratchets, like the Ares, Topeak, or Wiha.
With 60 teeth, and a locking flex-head that is only 18mm wide, the Rujoi is very versatile and efficient.

Construction Quality
The Rujoi is a high quality tool. It is machined flawlessly. All surfaces and edges are crisp. The ratchet mechanism, the flex-head mechanism, the switch, the button, everything moves smoothly and precisely, with excellent tolerances. There are no imperfections, no pitting, no burrs, no unfinished spots. Construction quality is as high as it gets with these.Portability
Compared to other ratchets we have seen so far, this is the longest, and it has the longest extension as well. This may interfere with edc pouches. The Rujoi will not fit in pouches and tins other ratchets will. If length is an issue, this may not be the best option.
It does come with a nice case, that is not extremely bulky. Of course, the foam insert that holds everything in place leaves a lot of unused space. This can be mitigated by simply making more holes in the insert to accommodate more bits, or just removing the insert completely.

Value
This set costs $40. Certainly a lot, but also worth it.
One of the best ratchet we have seen so far was the Prestacycle T-handle ratchet. It is interesting to compare that to the Rujoi, since they both offer the T-handle configuration, and cost the exact same amount.
The Rujoi is first and foremost a locking flex-head ratchet, so this is already a massive advantage.
The Rujoi comes with a more versatile case, that can hold much more, and can also be used for anything else. The Prestacycle wallet is much more restrictive. The Prestacycle can be bought with the exact same case as the Rujoi, but then it will cost $10 more.
The Rujoi comes with S2 steel bits. The selection is the same as the Prestacycle, but its bits are Chrome-Vanadium.
The Rujoi also comes with three sockets and a socket adapter. Not a big advantage, but the Prestacycle did not come with any.
And the main feature of the Prestacycle is not sacrificed. The Rujoi can also accept the long extension as a T-handle.
The Prestacycle is still one of the best value ratchets we have seen, so the Rujoi is also one by default.Conclusion
Comparing the Rujoi to the Prestacycle was unavoidable. They share the same ratchet head, and they both accept long extensions for a T-handle configuration. And the Rujoi has the edge in pretty much all categories compared to the Prestacycle, except length.Even when looking at the Rujoi by itself, it still comes out on top. It is very well-made, with a great bit selection. The bits are made out of S2 steel. It also has a socket adapter and three sockets. It also comes with a long extension and a handy case. It is also a locking flex-head ratchet. This comes in handy for fasteners in awkward places. The Rujoi can also be used with pretty much any double-ended bit. Bits can be removed easily thanks to the hole in the back of the head. This is not a small deal, since we have seen many ratchets struggle with bit removal. The Rujoi adds only 2mm to a bit's clearance, and has a narrow head as well.
The Rujoi seems to cover all the bases as far as edc ratchets go. The features go on and on, and the only compromise is the increased length, and a seemingly high -but fair- price compared to others. This is nothing short of impressive. The Rujoi has no real disadvantages to speak of. It is one of the best deals around, putting other ratchets to shame. Highly recommended.
Pros
-Flex-head feature provides versatility.
-High quality.
-High number of teeth.
-T-handle configuration allows for additional torque.
-Nigh pass-though head works with all double-ended bits.
-Better grip for people with large hands.
-Excellent assortment of S2 steel bits.Cons
-Possibly a little too long for edc.If you liked this ratchet, also check out:
Couldn't find one of these shipped to the UK so ordered a "KS Tools 918.1590 1/4 Inch Bit Joint Reversible Ratchet Set with Plug Adapter for Sockets, 3-Piece" for $42. The price is a bit steep compared to other fixed head options but I wanted a flexible head.
It's got a 60 tooth ratchet, the total length is a tad shorter than the Rujoi, at 117mm.
Overall the mechanism is nice and I'm pretty happy.
I've got pics but I think I need to upload to an image hosting site first? Visually very similar to the Rujoi, the 1/4 bit to 1/4 drive adapter is good.
-


-
That milwaukee ratchet looks like it could be used as fidget toy

-
Thank you for these reviews, RP!
I should be purchasing a bit ratchet sooner rather than later. A primary use would be tightening the screws on doorknobs, so a low profile is essential. Such a set wouldn't be something I'd tote around, so a compact case isn't a priority. The Hazet would be at the top of my list if it weren't for the price. Wera and Wiha have some pretty compelling offerings, too. Are there others I should consider? -
-
@Farmer X said:
Thank you for these reviews, RP!
I should be purchasing a bit ratchet sooner rather than later. A primary use would be tightening the screws on doorknobs, so a low profile is essential. Such a set wouldn't be something I'd tote around, so a compact case isn't a priority. The Hazet would be at the top of my list if it weren't for the price. Wera and Wiha have some pretty compelling offerings, too. Are there others I should consider?The Wiha won't be low profile, it adds a fair bit to a bit, and comes with standard bits. Wera is good, but expensive. Not low profile either.
For low profile , I recommend these:
-Kaifnt set with ultra stubby bits. The bits are 15mm long, and it has a very extensive bit set that includes Imperial and Metric Allen bits. And comes in a case.
-Mulwark with the two bit holders, it comes with 13 stubby bits and 6 standard bits. No case though.
-SK11 ratchet, and SK11 ultra stubby bit set, the bits will be only 12mm long, but no Imperial ones. Just Metric. No case.
-Vessel and Anex also come with stubby bits and have useful features.These are all sandwich ratchets. The only full metal ones that comes with stubby bits that I have reviewed so far are the Klein and Titan swivel head, but these are not low profile. They both add quite a lot to a bit's clearance.
If regular bits are fine, the Victorinox, Granite, Topeak, Ares, 711L, Giant, etc add no length to a bit. The Prestacycle, Wera, and Tone add only 2mm to a bit's clearance. Do not get the LaBear flat ratchet. It is smurf. And the Ovatt one with the pouch and belt clip is smurf too. The Zoyo is inexpensive and the ratchet is nice enough, but the carrying caddy will break and will not hold the ratchet for long. -
-
Regarding Blackburn Big Switch, FINALLY someone includes proper knurling on these things. It's a shame it's not around the shaft like leatherman bit extensions, but I'll take it.
711L just released a version of the mini ratchet with an end-bit holder deep enough to use double sided bits
so leatherman bits and maybe wiha double ended bits should be on the table, BUT this presumably precludes the use of the stubby steinwhale or other ultra-short bits.
I guess it's a tradeoff...https://www.amazon.com/711L-Mini-Ratchet-Wrench-Double-ended/dp/B09T9KY2LG/
I have one coming but it won't be here for a week or two. The "knurling" looks pretty much decorative, and these little guys can be slippery, so maybe someday they'll fix that and add leatherman like knurling. Hopefully this deeper bit well option will become the norm and we will see an articulated ratchet version of the stubby, and a long version of the stubby.
Titan made a stubby version with a handle bit well also:
https://www.amazon.com/dp/B0DVV76J5MUnfortunately this bit well is very shallow -- I just picked one up and it won't accept even the stubby steinwhale double ended bits, only regular 1" bits. Also it only comes in the bit driver version not the socket version. I have mixed feelings because while this is larger than the 711L type ratchets, and won't get into some small places, because the head articulates it kind of works like a sideways ratchet and an inline ratchet too which is nice. What I did was swapped the ball with the 1/4 square drive version, and drilled out the bit well and added another magnet so that I can use the steinwhale double ended bit as well as regular 1" bits, and I just leave the double ended bit in there.
-
Might be worth measuring your knobs (stop sniggering at the back!) to see how much clearance you have, I specifically bought the rujoi adjustable head ratchet for getting into awkward spots.
-
-
This looks quite nice, a design I haven't seen before. No brand name though.

-

Stanley Fatmax Mini Ratchet Set
Ratchet weight: 83g or 2.9oz
Set weight: 474g or 16.7oz
Length: 91mm
Head width: 23mm
Head clearance with standard bit: 30mm (adds 5mm)
Teeth count: 48
Minimum swing arc: 7.5°
Bit retention: magnet
Extension bit retention: magnet and locking
In-line driver: no
Bit material: Chromium-Vanadium steel
Handle material: Chromium-Vanadium steel
Price: $44 with 30 bits, locking extension, 7 sockets, case
Bits:
Phillips 1, 2, 3
Allen 3, 4, 5, 6
Torx 8, 10, 15, 20, 25, 27, 30, 40
TamperProof Torx 10, 15, 20, 25, 27, 30, 40
Slotted 4, 4.5, 6.5, 8
Pozidriv 1, 2, 3
Square socker drive adapter
Sockets 6, 7, 8, 10, 11, 12, 13Accessories
The Stanley Fatmax Mini Ratchet Set comes in a case, with 30 bits, a locking extension, and seven Metric sockets.The case is plastic, lined with a foam insert with holes for everything. In the lid, there is a picture with all the content specifications. The case closes securely. It more than passes the upside-down test with nothing falling out. The ratchet, sockets, and extension are held in securely. The bits are held very tightly, as if the material starts to stick onto them if left for a long time. They may require wobbling around to get them to pop out of the foam insert. The case is impressively compact, considering the amount of items it holds.
The 30 bits are Chromium-Vanadium. It is an extensive selection, but the big issue is corrosion, as they have developed rust in a few months.
The extension has a magnet and is also locking. It has also developed surface rust on the locking collar.
The 7 sockets are Metric and a socket adapter is included. These have developed some pitting, as has the ratchet.

Dimensions
At 91mm long, this is about average, although quite heavy, at 83g. It adds 5mm to a bit's clearance, and the head is 23mm wide, so a little wider than average there.
Teeth Count
Having 48 teeth seems a little low compared to how wide the ratchet head is. The teeth give a 7.5 degree minimum swing to engage the next tooth and turn a fastener. Not very impressive, but definitely good enough.Bit Retention
The ratchet has a magnet and the retention is definitely adequate. The extension is locking and also has a magnet, so bits will not fall out.Bit compatibility
Stubby bits sink in a little too deep. They can still be used, but removing them will not be easy.
Leatherman bits can be used just fine. The ratchet is not deep enough for regular double-ended bits.
Switch action
The switch has good detent in the frame, but has quite a lot of play. It can protrude outwards about a mm. The scalloped area that the switch slides in is much wider than the switch can move. This switch may have been made for another ratchet and used for this one to cut costs.Ease of use
The case lid can be used as a tray for spare parts. Bits feel glued onto the foam insert and require wobbling around to get them to come out. The ratchet is narrow behind the head, locking the index finger and thumb. The handle is a three-finger grip.
The main pro with this would be the resilience. The ratchet head is thick and definitely heavy duty, certainly more so than almost all other ratchets we have seen so far. This ratchet is among the heaviest and lacks a knurled wheel and an inline driver. The teeth count is slightly above average, with 48 teeth for a minimum swing of 7.5 degrees.
Construction Quality
The finish is consistent throughout but some pitting has developed on the ratchet and sockets. This is minor and nowhere near the level of rust on the extension collar and bits. These bits have arguably the worst finish so far. This set was purchased in April 2023, and many bits are just covered in rust. This is only surface rust and can be removed with little effort, but the issue still remains. The set has been kept in the same storage conditions as many other sets in this thread, with and without cases, and barely any have any rust, let alone this much.The ratchet switch has quite significant play in the frame. The ratcheting socket has barely any play. The ratchet head is held in place with a C-clip and can be disassembled.
Portability
Though quite heavy, this is short. It will fit in multi-tool pouch side-sleeves and even Altoids tins. It will of course fit in edc pouches but the ratcheting socket protrudes from the frame and may interfere with pouches closing neatly.
The case is definitely compact for what it holds, especially compared to other ratchet sets that come in cases. Still, the case is not small, and the set is among the heaviest yet. It will fit in a cargo pocket but may drag your pants to your ankles.
Value
For $44, this set is not a bad purchase, but a few caveats exist. First and foremost, this has developed rust in the almost two years of sitting in the same tool cabinet with about 30 other ratchet sets, bit sets, screwdrivers with bit storage, etc. Barely any other bit set has developed pitting, let alone rust, and at the extent of the Stanley set.
It is interesting to note that this set is the same as what comes with the Wera Tool Check. If it also had an inline driver, it would match the Toolcheck Plus in utility. Maybe not in longevity, considering the rust, but it will definitely be less expensive. And because it is a set in a case, you can still add a few more bits, or Allen keys, or other small items to it, which cannot be done easily with the Tool Check Plus holder.
Conclusion
The Stanley Fatmax Mini Ratchet set is definitely interesting. It is the most comprehensive set we have seen so far. And it is compact, with its case being essentially the same size as other ratchets sets, like the Bosch, GreaTalent, Kaifnt, while containing much more. It is even smaller than the Inwell ratchet set case, and it also holds more than that as well.However, this thread aimed to examine edc options, and neither the set nor the ratchet by itself are that impressive when it comes to that. The case and ratchet are among the heaviest so far. The ratchet may be short, but it does not offer many features as other ratchets do, especially when weight is considered. Be it weight, inline drivers, bit compatibility, teeth count, bit clearance, knurled finger wheel, price, and of course corrosion resistance, this will probably not win.
It is not all bad, but for edc, there is no reason to go with this.

Pros
-Comprehensive set, with ratchet, locking extension, 30 bits, 7 sockets
-Case has very little unused space.
-Heavy duty ratchet.Cons
-Has developed rust and pitting on everything in less than two years.
-High price.
-Bits are not easy to remove from case.
-Head is too wide for how many teeth it has.
-Bits are a little too tightly packed.If you liked this ratchet, also check out:
-
I don't know that there is a more comprehensive reviewing of mini ratchets to be found anywhere! :ahhh
This is an amazing and exhaustive list!
Def
-
[quote author=ReamerPunch link=topic=88713.msg2537271#msg2537271 date=1751826381]
This looks quite nice, a design I haven't seen before. No brand name though.Not seen the black design but a silver version is available from ZoyoSports. I tried to buy one myself off their website, they emailed me after a few days asking I pay an additional sum for shipping. Got refunded eventually. Might buy it though AliExpress if I see a good price, it never seems to be available as "free shipping above X" though.
-

Engineer DR-37 bit ratchet
Max torque rating: 93 Nm / 68 ft lb
Weight: 65g
Length: 92mm
Head width: 19mm
Head clearance with standard bit: 29mm (adds 4mm)
Teeth count: 72
Minimum swing arc: 5°
Bit retention: spring detent
In-line driver: no
Handle material: Carbon steel alloy
Price: $13 with no accessoriesAccessories
The Engineer DR-37 came with nothing. It is available with a few different sets of screw extraction stubby bits but these are quite expensive.
In Amazon US it can be found listed with a couple different sets of bits, as an Amazon Japan export, but these cannot be shipped to Australia, and they cannot be found at all in Amazon Japan itself. They are not even listed in Japanese mail forwarding sites that cover Amazon Japan.
So, at least for now, the best option is to get it on its own, or not at all (see below).
Dimensions
At 65 grams, this is on the heavier side of mini ratchets. It is 92mm long so about average. The head is 19 mm wide, certainly not the narrowest, but decent considering the teeth count.
It adds 4mm to a bit's clearance. Not bad.
Bottom right: LaBear Folding, CROM, Anvanna, Pro Bike, Railer, Engineer, Granite, Geinxurn, Klein, Milwaukee, PrestaCycle, Rujoi Flex-headTeeth Count
With 72 teeth, the DR-37 has a minimum swing of 5 degrees. Quite nice, and almost as good as it gets with mini ratchets.Bit Retention
Ah, here we are. Bits are held in with a flat omega spring. Retention is fine, not too tight, not too loose.
The thing is, this spring broke shortly after removing the ratchet out of the package, and with only inserting bits in it a few times.
No actual fasteners had been turned with it. The spring broke at one end. The ratchet can still be used. The spring still stays in the ratchet, bits are still held firmly with it.
Still, this is the only time we have seen a part break, and without even using it on fasteners, and on the first day out of the package, no less.Bit compatibility
Regular, stubby, and impact bits are just fine. The ratcheting socket is too shallow for double-ended bits, Leatherman bits, even the stubby double-ended Steinwhale bits.
Switch action
The switch is tiny but easy to operate. Detent is excellent.Ease of use
72 teeth for only 5 degrees minimum swing.
Excellent ergonomics, the handle is off-set and not slippery.
It has a knurled finger wheel that is metallic, not plastic.No double-ended bits fit in this.
The spring broke almost immediately out of the box, so it still functioning is irrelevant.
It is curious that this ratchet has the highest torque listing so far, at a reported 93 Nm / 68 ft lb, and yet it is the first ratchet that had a part break with virtually no use.
Construction Quality
The bit retention spring broke almost immediately out of the box, so it still functioning is irrelevant.
Finish is fine for what that is worth. The handle doesn't collect fingerprints and is not slippery in the slightest.
The ratcheting mechanism works as it should.
Portability
At 92 mm long, it fits comfortably in an Altoids tin. No issues with multi-tool pouch side-sleeves, edc pouches, pen sleeves.
It is a bit heavy, at 65 grams, but certainly not too much above average.
Value
At $13, this is fairly inexpensive. It would have been nice to see the options with bits actually be available for purchase. Maybe even with a case.Conclusion
Compared to some other options, it is a little unfortunate that the DR-37 comes with no accessories. It is also significantly more unfortunate that the bit retention spring broke without even getting a chance to use it.
This would have been a decent option for a mini ratchet. It is a nice design, with a knurled finger wheel, excellent ergonomics, a high teeth count. While a little heavy, it fits in Altoids tins and edc pouches. Still, this is the first failure we have seen, with something breaking, and not even by using it strenuously; or at all. Though not catastrophic, a failure is a failure. I cannot recommend it based on what has happened. I may have received a lemon, one-off bad unit, but even then, my review is based on what I got, not on what I might have gotten. Even if the spring had not broken, the ratchet is still not that available. The sets with bits are not available yet, and the sets with screw extraction bits are very expensive, and not all that useful for edc.
If you like this design, the Geinxurn is very similar to this and is one dollar more, for 20 impact rated bits, two bit holders, impact extension, and case. And nothing has broken in the four months I've had it.Pros
-Excellent ergonomics.
-72 teeth for only 5 degrees minimum swing.
-Handle is not slippery and does not collect fingerprints.Cons
-Bit retention spring broke shorty out of the box.
-Sets with bit holders and bits are not available anywhere.
-Sets with screw extraction bits are very expensive.
-Ratchet is heavier than average.If you liked this ratchet, also check out these:
-
@gravelmonkey said:
Not seen the black design but a silver version is available from ZoyoSports. I tried to buy one myself off their website, they emailed me after a few days asking I pay an additional sum for shipping. Got refunded eventually. Might buy it though AliExpress if I see a good price, it never seems to be available as "free shipping above X" though.At least there is a brand. How would I review and possibly recommend it with no brand? Thanks! I'll see if I can get my hands on one. I like the black one better I think.

-
@Grant Lamontagne said:
I don't know that there is a more comprehensive reviewing of mini ratchets to be found anywhere! :ahhhThis is an amazing and exhaustive list!
Def

There better not be!

-

Sharden Mini Ratchet Set
(can also be found branded by Justech)
Weight: 51g
Kit weight: 308g
Length: 94mm
Head width: 15mm
Head clearance with standard bit: 31mm (adds 6mm)
Teeth count: 48
Minimum swing arc: 7.5°
Bit retention: magnet
Extension bit retention: magnet and locking
In-line driver: no
Bit material: S2 steel
Handle material: Chromium-Vanadium steel
Price: $16 with 30 bits, locking extension, and case
Bits:
Tamperproof Torx 10, 15, 20, 25, 30, 35, 40
Spanner 2.8, 3, 3.5
Tamperproof Allen 4, 5, 6
Robertson 0, 1, 2, 3
Slotted 4, 5, 6
Phillips 1, 2, 3
Pozidriv 1, 2, 3
Spline 5, 6, 8
Square socket adapterAccessories
The Sharden ratchet comes with 30 S2 bits (S2 is not stamped on the bits, but mentioned on the case), a locking bit extension, and a plastic case. Everything fits in a hard plastic insert, which can also be removed. The ratchet and extension snap into their spots, but the bits are not held in place. Care must be taken when opening the case, to prevent the bits from falling out.The case does not have a proper hinge or latch. The whole case is one piece of plastic, with one half folding over the other, and the plastic is hair-thin at the folds. The two halves or the latch seem bound to just separate at any given moment.
The ratchet can fit on top of the extension, so the case could be narrower, or hold another row of bits, or even sockets.

Dimensions
This is extremely similar to the Bosch ratchet, and only has minor differences. The Sharden's neck right behind the head is a little thicker, and its end is a little pointier. The Sharden is also 3 grams heavier than the Bosch. Other dimensions are the same, like the length, head width, and bit clearance.
Like the Bosch ratchet, the Sharden's ratcheting socket also protrudes from the head, and the body is slightly offset, making it take some more space compared to flat ratchets.
Bottom right: LaBear Folding, 711L, Jackly, Leatherman, Ares, Wera, Tone, Wiha, Sharden, Bosch, Topeak, Blackburn, Zoyo, Victorinox, CyclingDeal, PrestaCycleTeeth Count
There are 48 teeth, which give a 7.5 degree swing arc. This is perfectly acceptable, and makes the ratchet rather easy to work with.Bit Retention
Bits are held in place with a magnet. The Sharden magnet is a little weaker compared to the Bosch ratchet's magnet.
The extension is a locking one, but the bits of the set do not lock in to it. Upon closer inspection, these bits have much shallower retention notches than other bits. Wera, Wiha, Bosch, Stanley, PB Swiss, all other brands of bits that were tested do lock in the Sharden extension.Bit compatibility
Stubby bits sink deep in the socket, and the magnet is strong enough to make them hard to remove.
Standard double-ended bits will not work since they are too long to engage and turn properly in the driver socket.
Leatherman bits can be used to an extent, since they can be turned, but only a short length engages with the bit socket, and they can move significantly from side to side.
Switch action
The switch has rather low detent. It has a flat base but sits on a curve, and it is also too long for the frame. This makes it protrude quite significantly from the frame, making it easy to catch on objects. Combined with the low detent, it is easy for the switch to be bumped accidentally.Ease of use
The handle is off-set from the head and has a narrow neck but flared body. This helps ergonomics, with the narrow neck offering a natural position for the user's fingers. The flared body also fills the hand and is nicely chamfered. The narrow head and decent teeth count also aid in ease of use.
The set sits nicely in the case. All parts are easily identifiable and accessible without getting in each other's way.
The switch is rather poorly designed, seeing how much it protrudes and how weak the detent is.
The Sharden ratcheting action is a little stiff. The Bosch ratchet feels like it turns much more smoothly.
There is no knurled finger wheel and no in-line bit socket.The Bosch ratchet has slightly better ergonomics thanks to its thinner neck, but the Sharden's thicker neck makes it more durable, and it is still comfortable in hand.

Construction Quality
The ratchet appears well made. The bits fit in well with minimal play. The body is highly polished with no grind marks or imperfections. Edges are nicely chamfered. The magnet is strong and holds the bits firmly.
The ratcheting mechanism has some play in the frame, but this is minimal and does not hinder performance.
The switch has some wobble to all directions, and protrudes way too much. This may have been made for another ratchet, and simply used for this one to cut costs. The ratcheting action feels just a touch crunchy and stiff compared to other ratchets.The case suits the set. Everything sits in there neatly. The ratchet does fit on top of the extension with the case still able to close properly. The case could either fit more accessories, or be about three fourths the width it is.
The case hinges seem like obvious weak points. There is no actual hinge pin or pivoting parts, divots, etc. The two plastic halves are just integrally attached to each other but barely so. This kind of thin, folding plastic for a hinge is mostly seen on disposable containers, like gum, M&M's, mints, etc. This ratchet set case will not last long.Bit construction is arguably the biggest issue.
The #4 Allen bit does not fit a #4 Allen fastener. All other bits that were tested fit their respective fasteners, but I do not have enough types and sizes to check every bit. This has never been a problem up to this point.
These bits do not lock in the extension they come with. Their retention notches are not deep enough for the extension's ball detent to engage properly and lock them. They are still held very tightly, and there might not be any issue, but at the same time, the bits do not lock in their locking extension or any other locking extension that was tested. This is not good.Portability
Although short and thin, the ratchet may be awkward to carry in a pouch, due to the elongated ratcheting socket. This protrudes enough already, and the handle is off-set in the opposite direction, making the ratchet take more space than it would seem.
It being a set, it makes sense to leave it in its case. Although it will fit in a cargo pocket, there will be some rattle, and it will take way too much space for what the set has. The ratchet is still on the small side, so it will fit in pouches with its bits, although a bit sleeve will be needed to carry them.
Value
This kit is inexpensive and quite thorough. There are thirty bits, made out of S2 steel, and a locking bit extension. It does seem like a good deal for $16. But is it?Conclusion
So far, average ratchets that came with bit sets were just that; average. They were good enough, they worked, but what made the sets good were the bits, sockets, extensions, etc. This is not the case for the Sharden ratchet set. The attention seems to have been given to the nice, shiny, thirty S2 steel bits, but it was not. The #4 Allen bit does not work with those fasteners and no bit locks in the locking extension.Features such as the sub-optimal shape for edc, good ergonomics, lack of a knurled finger wheel and in-line driver, all these are arguably insignificant now. I cannot recommend a ratchet that may come with bits that do not work. Every single ratchet so far, even the absolute worst, came with perfectly fine bits that worked. And this ratchet is not good enough by itself to make the whole set worth purchasing.
I cannot tell for sure if this is a copied design of the Bosch ratchet or just one from the OEM who makes the Bosch ratchet. The Bosch ratchet has a few differences, and it has held up for over three years of intermittent use. And the bits fit their fasteners and lock in locking extensions. And the case is two separate pieces of plastic attached by a long steel hinge pin, and the latch is an integral, thick piece of the lid. If you like the design of the Sharden ratchet, get the Bosch set instead.
Pros
-30 S2 steel bits.
-Good ergonomics.
-Inexpensive.Cons
-Allen #4 bit does not fit in Allen #4 fasteners.
-Bits do not lock in the locking extension they came with.
-Case leaves a lot of unused space.
-Ratcheting switch protrudes way too much.
-No in-line bit driver.
-Sub-optimal shape for edc.If you liked this ratchet, also check out:
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



















































