EDC Bit Ratchets
-

Geinxurn mini ratchet set
(Ratchet can also be found branded by Aramox, Astro, CarbHome, Cotouxker, Duratech, Generic, Hi-Spec, Keenso, Nothers, Owl Tools, Panshiyon, Sunex, Triple Deer, Ybeki)
Warranty:
Weight: 58g
Set weight: 218g
Length: 94mm
Head width: 19mm
Head clearance with standard bit: 32mm (adds 7mm)
Teeth count: 72
Minimum swing arc: 5°
Bit retention: magnet
In-line driver: no
Extension retention: magnet and ball bearing
Bit material: S2 steel
Handle material: Chromium-Vanadium steel
Price: $14 with 20 bits, 2 rubber bit holders, extension, case
Bits:
Phillips 1, 2x 2, 3,
Torx 7, 8, 9, 10, 2x 15, 2x 20, 3x 25, 27
Slotted 8
Square 2Accessories
The Geinxurn mini ratchet comes with an extension, two rubber bit holders, 20 bits, and a bit case to store everything.The extension is impact rated, with a torsion zone, and both a magnet and ball bearing for bit retention.
The bits are also impact rated with torsion zones. There are ten Torx bits in one bit holder, and a total of four Torx bits that are repeats.
It would have been nice to see these four repeated Torx be Allen bits or at least non-repeats. The bit size is printed on the bits, and will rub off with extended use.The bit holders are transparent rubber. The retention is fine. They are marked with Geinxurn on one side and the bit sizes on the other.
The case is a bit box or tackle container, divided into two compartments. The two halves are attached with two hinges and not just with a hair-thin line of plastic.
This case is used for a few variations of kits by Geinxurn, so for this specific set there is some unused space. There is room for a few bits next to the two bit holders, and an entire bit holder can squeeze in with the ratchet and extension.
The latch is a separate piece that engages the lid securely.
Dimensions
At 94mm long, this is about average. It is not exactly lightweight, at 58 grams, but certainly not bad.
Bottom right: LaBear Folding, CROM, Anvanna, Pro Bike, Railer, Engineer, Granite, Geinxurn, Klein, Milwaukee, PrestaCycle, Rujoi Flex-headTeeth Count
With 72 teeth, this is on the upper end of mini ratchets, which is quite unusual for such an inexpensive set.Bit Retention
Bits are held with a magnet which feels of above average strength. Removing stubby bits with thin tips may require pliers.
The extension has both a magnet and ball bearing. This holds bits very securely, but again, stubby bits will require pliers.Bit compatibility
Stubby bits can be used but may need pliers to remove.
Neither the ratchet nor extension are deep enough to use double-ended bits.
Leatherman bits barely engage and have too much play.
Switch action
The switch is small and tucked behind the head. It has adequate detent and did not get moved accidentally.Ease of use
Everything fits in the case nicely with room to spare. Bits can be identified instantly.
They fit in the extension and ratchet perfectly. In the extension, there is no wobble at all, thanks to the ball bearing.
The ratchet has 72 teeth, so it has a minimum swing of only 5 degrees.
The ratchet handle is off-set and flat, offering excellent ergonomics, with a proper, comfortable three-finger grip.
The case lid sits flat when open, so it can be used as a tray for spare parts.
Construction Quality
This set feels much more expensive than it is. The bits and extension are impact-rated, with proper torsion zones, and crisp finish.
The ratchet feels great in the hand, with everything nicely chamfered, a dull, crisp finish.
The bit holders are transparent with the text printed on flawlessly.
The case is a simple but nice bit box, with no molding imperfections.The entire set feels impressively well-made for what it costs. Nothing feels cheap. Metal, rubber, plastic, all materials feel properly formed and put together.
Portability
The ratchet is not the best shape for edc. The handle is off-set, and the ratcheting bit driver protrudes from the head. There are certainly thinner, slimmer ratchets out there.
Still, this is still a mini ratchet, and fits in the usual pouches and bags.The case is flat, and although there is unused space, it is still smaller than sets that hold the same amount of components.
Having the two rubber bit holders is an excellent addition, as it allows users to ditch the box and have everything in a pouch, with the bits being in their original, nice bit holders instead of being loose and needing third-party bit holders or other solutions.
Value
At $14 for 20 bits, extension, bit holders, and case, this is one of the most inexpensive and at the same time complete sets we have seen.
Taking into account the build quality, this is an excellent value for money.
Conclusion
The Geinxurn ratchet can be found under many, many brands. The same cannot be said for the Geinxurn ratchet set. This was one of the most surprising sets so far.
Every component of this set feels like it costs a lot more than it does. The bits and extension are excellent, impact rated, precise, proper.
The ratchet has 72 teeth, excellent ergonomics, a flawless finish.
The bit holders are transparent, with perfect text, great retention, soft and bendy, with no imperfections.
Even the case feels nice; thick, good quality plastic, with proper, real hinges, and a proper, strong latch that holds the set closed securely.This is very reminiscent of the Tone BRS20C ratchet set. Ratchet, extension, 20 bits in two bit holders, and a nifty compact case.
Of course, the Tone ratchet is much higher quality, with more features, and the set is even more compact. On the other hand, the Geinxurn set is half the price, has more teeth, and is readily available and surprisingly solid.The Geinxurn was undoubtedly a breath of fresh air. This set is nothing short of impressive. Every single component feels nice, properly made, and way above what the price would suggest. If you are looking for a good, inexpensive ratchet set, this is certainly a good option, with some room for improvement.

Pros
-Inexpensive.
-No component feels cheap.
-72 teeth.
-Impact rated extension and bits.
-Excellent ergonomics.Cons
-Some redundancy in bits.
-Case has some unused space.
-Adds 7mm to bit clearance.
-Bit size is printed on bits and will rub off.
-Shape not ideal for edc pouches. -

CROM mini ratchet
(Can also be found branded by LaBear.
Same design as 711L and Signet, but those have 52 teeth and are not t-handle capable)Weight: 20g
Extension weight: 20g
Length: 52mm
Head width: 15mm
Head clearance with standard bit: 25mm (adds 0mm)
Teeth count: 60
Minimum swing arc: 6°
Bit retention: spring
In-line driver: magnet
Extension retention: magnet
Handle material: Chromium-Vanadium steel
Price: $20 with extension and foam trayAccessories
The Crom mini ratchet comes with an extension and a foam tray.
The extension can be used as a regular extension in the ratcheting end, or to increase the length of the ratchet, for additional torque and comfort.
The extension can be used as a t-handle for the ratchet's inline driver when the marked edge is aligned with the dot on the ratchet face.
Dimensions
The Crom shares its design with the 711L and Signet mini ratchets, being 52mm long and with a 15mm wide head.
At 20 grams, this is second only to the 711L mini ratchet, which is 19 grams.
Bottom right: LaBear Folding, CROM, Anvanna, Pro Bike, Railer, Engineer, Granite, Geinxurn, Klein, Milwaukee, PrestaCycle, Rujoi Flex-headTeeth Count
The Crom mini ratchet has 60 teeth, and a 6 degree minimum swing.
This is impressive, and unique, since the head appears to be the same as the 711L, Topeak, Giant etc, but all those have 52 teeth, which means that this is the narrowest head for how many teeth it has.Bit Retention
The Crom uses the same rectangular spring as the Topeak, Granite, PrestaCycle, etc ratchets. Bit retention is excellent. Thanks to the hole in the head, bits can be disengaged from the spring by pushing them from the back.Bit compatibility
Stubby and regular bits fit perfectly. Impact bits with the grooved neck do not engage the spring, and while there is some play they will not fall out.
Double ended bits and Leatherman bits also fit nicely thanks to the hole in the back of the ratchet head.
The in-line driver and extension have strong magnets and are somewhat deep, so stubby bits cannot be removed with just fingers.
Leatherman bits can be kind of used, but they barely engage and will have too much play left and right.
Standard double-ended bits cannot be used for in-line driving or the extension. They do not engage and cannot be turned with the tool.
Switch action
The switch is tiny but easy to operate, with excellent detent.Ease of use
The Crom mini ratchet is long enough for a two-finger grip, but this can be addressed easily with the extension or a long bit.
The extension can also be used as a t-handle for the inline bit driver, should you require more torque for a stubborn fastener.
There is also a knurled finger wheel for speed-turning loose fasteners.
The hole in the ratchet head allows for double-ended bits and Leatherman bits.
Thanks to the almost pass-through head, this will add no length to an inserted bit.
Construction Quality
The same high quality as its kin, the Crom is an excellent little tool. The finish is consistent and flawless.
Everything is chamfered and polished, the mechanism works perfectly, the extension fits through the ratchet head perfectly.Portability
A major selling point of this ratchet, portability is about as good as it gets.
The Crom weighs only 20 grams, and thanks to the hole in the ratchet head, it is perfect for a keychain.
Thanks to the inline driver it can hold a bit while on your keys.
The extension does not have any carry options, and simply having it in the inline driver may be too long for keychain-carry.
The extension and ratchet will be about the same length as an average mini ratchet, with the added benefit of being a ratchet and extension set, and the ability to be used in the t-handle configuration.
Value
For $20, the ratchet and extension may seem just a little overpriced, compared to a few sets we have seen. Still, compared to other micro ratchets, this is quite appealing.Conclusion
The Crom mini ratchet appears to be a rebranded 711L/Signet mini ratchet. Fair, as it looks identical, but wrong. Although the Crom has the same head as the 711L etc, the internals are different.
The 711L has 52 teeth, but the Crom has 60. This is not a big difference, but it is an advantage for the Crom.
Of course, the Crom has the t-handle capability, which the 711L does not.
Also, the Crom with t-handle extension costs the same as the 711L which comes with nothing. Considering all this, there is no reason to get the 711L over the Crom. The Crom does more and costs the same.Like the 711L, the Crom has no disadvantages to speak of. It may seem too short for a proper grip, but this can be remedied instantly with the extension in the inline driver.
It is perfect for a keychain, although the extension will have to go in a pouch or wallet. The t-handle configuration allows for more torque and is a nifty feature.
Of course, this is of the same high quality as its kin, with an excellent finish and construction.The 711L instantly dominated the keychain ratchet domain when it was first released, and it seemed that there was no competition.
Well, this is no longer the case. Even though the Crom mini ratchet looks identical to the 711L, it has more teeth and is t-handle capable, and it costs essentially the same.
Until another mini ratchet with the same dimensions but more features appears, the Crom is the undisputed champion of keychain ratchets.
Pros
-Perfect keychain ratchet; lightweight, short, hole in the head for attaching clip.
-Retains features of similar ratchets (inline driver, knurled wheel, hole in head, great quality).
-More teeth than ratchets with the same head.
-T-handle capable.
-Has an inline driver:
-Can drive inline.
-Can store a bit while on a keychain.
-Can store an extension or long bit and be the same length as the Topeak.Cons
-None. -
When you posted the Crom a few months ago, I immediately bought one. Very cool mini ratchet and still enjoying it!
-
Heads up for fans of Klein Tools. Klein will be releasing a smaller version of the 32787 Mod Box bit and driver set that has the bit ratchet. The smaller set will have part number 32787S. It has the smaller compact Mod Box and ratchet bit driver. The set will now have a hex to 1/4” drive adapter which the larger set was missing. I will be picking up this set once it releases. I hope this will help someone out.
RP, I didn’t know where else to put this. This seemed like the most logical place since it contains a bit ratchet.
JonesE
-
Blackburn down to $32 from $38 :ahhh
Mulwark set down to $10 from $16 :ahhh
And that no brand one with the holder now branded Rock Bros (but double the price) :(
@JonesE said:
Heads up for fans of Klein Tools. Klein will be releasing a smaller version of the 32787 Mod Box bit and driver set that has the bit ratchet. The smaller set will have part number 32787S. It has the smaller compact Mod Box and ratchet bit driver. The set will now have a hex to 1/4” drive adapter which the larger set was missing. I will be picking up this set once it releases. I hope this will help someone out.RP, I didn’t know where else to put this. This seemed like the most logical place since it contains a bit ratchet.
JonesE
That looks like an awesome little ratchet! Thanks for sharing!

-

Milwaukee mini ratchet
Warranty: Lifetime
Weight: 77g
Bit kit weight: 25g
Length: 109mm
Head width: 20mm
Head clearance with standard bit: 35mm (adds 10mm)
Teeth count: 90
Minimum swing arc: 4°
Bit retention: spring and magnet
In-line driver: no
Bit material: Chromium-Vanadium steel
Handle material: Chromium-Vanadium steel
Price: $22 with 5 stubby bits and bit holder
Bits: Phillips 1 and 2, Slotted 3/16" and 1/4", 1/4" square adapter
Features: 5/16" (8mm) nut driver, integral carabiner/finger loop, knurled finger wheelAccessories
The Milwaukee mini ratchet comes with five stubby bits and a bit holder.
The bit holder holds the bits securely. It has a loop to attach to the ratchet's integral carabiner. It has the bit sizes clearly visible next to each bit place. When attached to the ratchet, the shape of the bit holder sits perfectly against the ratchet, but will swing freely. It would have been even nicer if the bit holder would attach magnetically on the ratchet, or with pins, or something that would make the set one solid, silent piece. The bit holder is a little wider than it could have been.
The bits are stubby. Even the socket adapter is stubby, which is unusual.
The Klein 65200 mini ratchet comes with the exact five bits the Milwaukee does.
Dimensions
Definitely on the larger side of mini ratchets, the Milwaukee is 109mm long and weighs 77 grams. It is hefty and bulky, and arguably awkwardly so. The head is tall due to the 8mm nut driver on the back, and the other end is also very wide, due to the integral carabiner.
Bottom right: LaBear Folding, CROM, Anvanna, Pro Bike, Railer, Engineer, Granite, Geinxurn, Klein, Milwaukee, PrestaCycle, Rujoi Flex-headTeeth Count
The Milwaukee has 90 teeth. This is interesting, considering that the Klein 65200 mini ratchet, which has seemingly the same head as the Milwaukee, has 72 teeth. 90 teeth means the Milwaukee has a minimum swing arc of 4 degrees.Bit Retention
The Milwaukee has good but not overly tight bit retention. The stubby bits it comes with can be removed easily with fingers. The Klein, which shares the head and retention system of both spring and magnet, had much firmer bit retention.Bit compatibility
Double-ended bits do not engage and cannot be turned. Leatherman bits barely engage and have significant play side-to-side.
Switch action
The switch is very short and flat. It would be very difficult to have it accidentally bump against something and have the ratchet direction change. It has good retention, and it is very easy to operate.Ease of use
Pretty much as good as the Klein mini ratchet.
The knurled finger wheel protrudes enough from the head and it is the easiest wheel to operate so far. The ratchet is long and provides excellent torque. The stem is flat compared to the cylindrical ones of most ratchets. This helps with grip and comfort. The finger loop allows for various grip configurations.
The head is narrow and has a high teeth count, even higher than the Klein.
Due to the 5/16" nut driver on the back of the head, the head is arguably taller than is needs to be. It adds 10mm to an inserted bit's clearance, which is the second worst, behind the Titan swivel-head ratchet, which adds 13mm. Stubby bits will aid in reaching fasteners in tight spots, but it only comes with four.
Construction Quality
The Milwaukee mini ratchet is very well-made. The finish is flawless. The moving parts operate smoothly with no issues whatsoever.
The carabiner gate has excellent retention and stays in the frame convincingly.Portability
The main focus of the Milwaukee ratchet in comparison to the Klein was portability. The fixed loop has evolved into an integral carabiner, and is the best of both worlds. The carabiner eliminates the need for additional clips, works as intended, and there is still plenty of room to use the loop in various grips, just like the Klein. Ergonomics are unaffected, which is a pleasant surprise, considering the placement of the spring gate.
The bit holder is also designed to attach to the carabiner, allowing for a few bits to piggy-back.
The ratchet is still a little heavy for edc, and rather awkward to store in an edc pouch. The head and carabiner end are much wider than conventional mini ratchets. Where a Mulwark/Topeak/Wera etc could slide into a wallet, pen sleeve, edc pouch, the Milwaukee cannot.

Value
At $22 with five stubby bits, this may seem as average, but compared to the Klein, it only gets better.Conclusion
The Milwaukee mini ratchet is the evolution of the Klein 65200. Fortunately, there are only improvements here.
The finger loop is now an integral carabiner, with the same ergonomics. The bit holder can be attached to the ratchet or your keys. The head has 90 teeth compared to the Klein's 72. The bit retention is much more forgiving. Both come with the same bits, so nothing was lost. The Milwaukee costs two dollars less than the Klein. Last and arguably most important, the Milwaukee has a lifetime warranty, compared to the Klein's one-year warranty. This is an obvious and significant upgrade. If you were thinking of getting the Klein, the Milwaukee offers more and costs less. Where the similarities end, the Milwaukee keeps going.This is recommended over the Klein, but do keep in mind that it is still long, heavy, adds 10mm to a bit's clearance, and will not fit in an edc pouch as effortlessly as most other mini ratchets. If you are looking for a slim, lightweight mini ratchet to tuck into your wallet, maybe keep looking.

Pros
-Lifetime warranty.
-90 teeth.
-Integral carabiner.
-Well-made.
-Excellent ergonomics.
-Finger loop allows various grips and tethering options.Cons
-Heavier than average.
-Head adds 10mm to bit clearance.
-With no bit inserted, the head is 20mm tall.
-Comes with only 5 bits.
-One end is very wide due to carabiner loop.If you liked this ratchet also check out:
-
The stats so far.
I have not included price because many have changed.
The Leatherman ratchet adapter is not included because it is not a bit ratchet.

-
Oh boy...


-
Wera also has a bicycle set in a nice wallet like the PrestaCycle, but it is double the price of the PrestaCycle. >:(

-
-
@ReamerPunch said:
Oh boy...
That looks like a pretty nice set, though the ratchet seems a little bulky for my liking.
-
-
Silly question. But would threading your keychain through the ratchet head eventually wear it out? I've had a few things wear eventually.
-
@Old Boy said:
Silly question. But would threading your keychain through the ratchet head eventually wear it out? I've had a few things wear eventually.Theoretically it might I suppose. I have a 711L mini ratchet on my keys, with a copper circle carabiner, so it is softer than the ratchet head, so it will wear before the ratchet does. So, if you are going to attach a mini ratchet to something with a carabiner, get a soft metal carabiner, like aluminium, copper, or brass, and you should be ok.
-
@ReamerPunch said:
I wouldn't say it's bulky.
I took a look at the doorknobs in my apartment. Much to my surprise, they appeared to be press-fit. None of them have any visible screws. So it'll probably be a while before I have any great need for a bit ratchet. I'll continue to follow this thread with interest, though.
-
@ReamerPunch said:
Theoretically it might I suppose. I have a 711L mini ratchet on my keys, with a copper circle carabiner, so it is softer than the ratchet head, so it will wear before the ratchet does. So, if you are going to attach a mini ratchet to something with a carabiner, get a soft metal carabiner, like aluminium, copper, or brass, and you should be ok.Thanks!!!

-
@ReamerPunch said:
So, if you are going to attach a mini ratchet to something with a carabiner, get a soft metal carabiner, like aluminium, copper, or brass, and you should be ok.Copper or brass will probably be chrome plated and that's hard. If you're worried about wear from your attachment method, only a plastic carabiner or cord seem safe. But my hunch is that wear from the carabiner is probably not the main source of failure in a ratchet.
-
I'm totally obsessed with this thread. Thank you for doing all the work.
Regarding tooth count, I get it that the higher the number the better in small spaces, but I believe that also limits the level of torque you can exert. Eg High teeth count = low torque, low teeth count = high torque.Anyone know what's the sweet spot for tooth count for these mini-ratchets? Like I totally can see why low teeth count is better for the larger ratchets.
I work in an office and occasionally use my tools so would love to hear from the super users out there.
-
@Old Boy said:
I'm totally obsessed with this thread. Thank you for doing all the work.
Regarding tooth count, I get it that the higher the number the better in small spaces, but I believe that also limits the level of torque you can exert. Eg High teeth count = low torque, low teeth count = high torque.Anyone know what's the sweet spot for tooth count for these mini-ratchets? Like I totally can see why low teeth count is better for the larger ratchets.
I work in an office and occasionally use my tools so would love to hear from the super users out there.
First of all, thank you so much for the enthusiasm.

I do not know the answer but I would also like to know.
Many ratchets come with a max torque rating, but I have not included it here because most ratchets do not list it and for many it is impossible to find.There are 40 bit ratchets reviewed in this thread so far (plus the Leatherman ratcheting adapter).

The teeth count varies from the abysmal 12 all the way to 90.
12 teeth: only one ratchet, so this is maybe considered too low.
16 teeth: 6 ratchets
36 teeth: two ratchets
38: only the Victorinox
46: only the Inwell
48: three ratchets
52 teeth: six ratchets
60 teeth: nine ratchets
72 teeth: seven ratchets
90 teeth: three ratchets16 teeth seems to be the norm with sandwich ratchets. And they work just fine. They all do. Teeth count has never been an issue for me. I do not use these to disassemble the Sydney Harbour Bridge, so they're ok. Sure, 72 or 90 teeth give a nice low angle of return if there is very limited space to swing the ratchet, but I have not encountered such a tricky fastener placement yet. Teeth count seems to be independent from price and quality. The Hazet is the most expensive and has 90 teeth, but so does the Titan. The Wera is expensive and has 60, but the Geinxurn is among the least expensive and has 72. The Mulwark has 16 and is kind of crude and cheap. The Anex also has 16 but is excellently finished and of very high quality.
Sure, the Wera is tougher than the Topeak, but it is more heavily built, so teeth count is secondary for this. The Hazet is probably the most robust, and has 90 teeth. The Stanley is also heavy built but has only 48 teeth.
The sandwich ratchets are not as resilient as one-piece ratchets, so maybe that's why 16 teeth is so common with them? Although that new Vessel sandwich ratchet is a sandwich design and has 60 teeth.
Until an expert comes along and enlightens us, all this seems to be dealer's choice.
I suggested Project Farm review mini bit ratchets, so I'm hoping we see a cool video in the future. :D
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login






















































