EDC Bit Ratchets
-
The stats so far.
I have not included price because many have changed.
The Leatherman ratchet adapter is not included because it is not a bit ratchet.

-
-
Oh boy...


-
Wera also has a bicycle set in a nice wallet like the PrestaCycle, but it is double the price of the PrestaCycle.


-
-
-
-
-
@Old Boy said:
Silly question. But would threading your keychain through the ratchet head eventually wear it out? I've had a few things wear eventually.Theoretically it might I suppose. I have a 711L mini ratchet on my keys, with a copper circle carabiner, so it is softer than the ratchet head, so it will wear before the ratchet does. So, if you are going to attach a mini ratchet to something with a carabiner, get a soft metal carabiner, like aluminium, copper, or brass, and you should be ok.
-
@ReamerPunch said:
I wouldn't say it's bulky.
I took a look at the doorknobs in my apartment. Much to my surprise, they appeared to be press-fit. None of them have any visible screws. So it'll probably be a while before I have any great need for a bit ratchet. I'll continue to follow this thread with interest, though.
-
@ReamerPunch said:
Theoretically it might I suppose. I have a 711L mini ratchet on my keys, with a copper circle carabiner, so it is softer than the ratchet head, so it will wear before the ratchet does. So, if you are going to attach a mini ratchet to something with a carabiner, get a soft metal carabiner, like aluminium, copper, or brass, and you should be ok.Thanks!!!

-
@ReamerPunch said:
So, if you are going to attach a mini ratchet to something with a carabiner, get a soft metal carabiner, like aluminium, copper, or brass, and you should be ok.Copper or brass will probably be chrome plated and that's hard. If you're worried about wear from your attachment method, only a plastic carabiner or cord seem safe. But my hunch is that wear from the carabiner is probably not the main source of failure in a ratchet.
-
I'm totally obsessed with this thread. Thank you for doing all the work.
Regarding tooth count, I get it that the higher the number the better in small spaces, but I believe that also limits the level of torque you can exert. Eg High teeth count = low torque, low teeth count = high torque.Anyone know what's the sweet spot for tooth count for these mini-ratchets? Like I totally can see why low teeth count is better for the larger ratchets.
I work in an office and occasionally use my tools so would love to hear from the super users out there.
-
@Old Boy said:
I'm totally obsessed with this thread. Thank you for doing all the work.
Regarding tooth count, I get it that the higher the number the better in small spaces, but I believe that also limits the level of torque you can exert. Eg High teeth count = low torque, low teeth count = high torque.Anyone know what's the sweet spot for tooth count for these mini-ratchets? Like I totally can see why low teeth count is better for the larger ratchets.
I work in an office and occasionally use my tools so would love to hear from the super users out there.
First of all, thank you so much for the enthusiasm.

I do not know the answer but I would also like to know.
Many ratchets come with a max torque rating, but I have not included it here because most ratchets do not list it and for many it is impossible to find.There are 40 bit ratchets reviewed in this thread so far (plus the Leatherman ratcheting adapter).

The teeth count varies from the abysmal 12 all the way to 90.
12 teeth: only one ratchet, so this is maybe considered too low.
16 teeth: 6 ratchets
36 teeth: two ratchets
38: only the Victorinox
46: only the Inwell
48: three ratchets
52 teeth: six ratchets
60 teeth: nine ratchets
72 teeth: seven ratchets
90 teeth: three ratchets16 teeth seems to be the norm with sandwich ratchets. And they work just fine. They all do. Teeth count has never been an issue for me. I do not use these to disassemble the Sydney Harbour Bridge, so they're ok. Sure, 72 or 90 teeth give a nice low angle of return if there is very limited space to swing the ratchet, but I have not encountered such a tricky fastener placement yet. Teeth count seems to be independent from price and quality. The Hazet is the most expensive and has 90 teeth, but so does the Titan. The Wera is expensive and has 60, but the Geinxurn is among the least expensive and has 72. The Mulwark has 16 and is kind of crude and cheap. The Anex also has 16 but is excellently finished and of very high quality.
Sure, the Wera is tougher than the Topeak, but it is more heavily built, so teeth count is secondary for this. The Hazet is probably the most robust, and has 90 teeth. The Stanley is also heavy built but has only 48 teeth.
The sandwich ratchets are not as resilient as one-piece ratchets, so maybe that's why 16 teeth is so common with them? Although that new Vessel sandwich ratchet is a sandwich design and has 60 teeth.
Until an expert comes along and enlightens us, all this seems to be dealer's choice.
I suggested Project Farm review mini bit ratchets, so I'm hoping we see a cool video in the future.
-
WorkPro ratchet is in.


-
-
@ReamerPunch said:
I suggested Project Farm review mini bit ratchets, so I'm hoping we see a cool video in the future.
Thank you for the detailed answer. I think Project Farm is one of the best channels out there.
In my opinion I think the more teeth the better since as you said mini ratchets are more for less robust task. I say this because I had to install a battery bracket for my car one time and the Klein ratchet was the exact length of free space in the wheel well of the trunk and my back was complaining the whole time as I could only swing the ratchet a little at a time. All I could think of was how I should bought something better from your list. -
Blackburn down to $27 from $38 :ahhh
Topeak up to $45 from $31
Yeah, Blackburn has lifetime warranty, Topeak only 2 years with original receipt. If you were thinking of getting one or the other, I'd jump on the Blackburn now. Check the reviews by clicking on the buttons at the top of the page.Wera up to $35 from $32 :-
For less than double that, you can find the Tool-Check Plus (I found the Tool-Check plus 1 for $67.5). Ratchet, extension, 30 bits, 7 sockets, mini bit driver, and a holder for everything.
Or get the Tone set for $32. Same head, weight, length, 20 bits, arguably the best extension so far in this thread, and a case with belt clip.And a new PrestaCycle t-handle ratchet.

-

Pro Bike ratchet set
(Ratchet can also be found branded by Feedback, LaBear, Machoman)
Weight: 61g with no extensions
Weight: 99g with both extensions
Set weight: 195g
Length: 75mm with no extension
Head width: 17mm
Head clearance with standard bit: 33mm (adds 8mm)
Teeth count: 90
Minimum swing arc: 4°
Bit retention: magnet
Extension retention: magnet
In-line driver retention: magnet
Bit material: Chromium-Vanadium steel
Handle material: Chromium-Vanadium steel
Price: $32 with 10 bits, bit holder, 2 extensions, wallet
Bits:
Phillips 1, Torx 25, 30, Flat 4, Allen 2, 3, 4, 5, 6, 8Accessories
The Pro Bike t-handle mini ratchet comes with two small extensions, a bit holder with 10 bits, and a tiny case.
The bits are very well made and fit their respective screws properly.
The bit holder is hard plastic. A rubber one would have been a little thinner.
The case is a clamshell, crush-resistant pouch, with a zipper and a belt-loop on the back. Inside it has a mesh pocket on each side.
With everything in one side, the other side is limited to thin items like a couple of credit cards, etc.
Dimensions
The main unit is 75 mm long with no extension installed, so extremely short, and weighs 61 grams, so definitely hefty.
The entire kit in the case weighs 99 grams, which is not all that much.
Bottom right: LaBear Folding, CROM, Anvanna, Pro Bike, Railer, Engineer, Granite, Geinxurn, Klein, Milwaukee, PrestaCycle, Rujoi Flex-headTeeth Count
The ratchet has 90 teeth, which is the highest we have seen so far, tying with the Titan swivel-head and Hazet mini ratchets.
This is more important with this ratchet, because of the two inline drivers.
Even with no extension in the top inline driver, the driver extends a little from the ratchet head, compared to regular ratchets. This makes this ratchet even more prone to obstructions.Bit Retention
All bit drivers on this set have magnets. All are of above average strength, and will work just fine.Bit compatibility
No bit driver is deep enough for double-ended bits.
Regular, stubby, long, and impact bits are fine.
Switch action
The switch feels just a little weaker than average, but it still has decent detent, and does not get reversed accidentally.Ease of use
This design is set up as a t-handle ratchet, with the short extension in either end. This provides excellent torque, considerably more than regular mini ratchets we have seen.
Of course, all connections are 1/4" hex, so many configurations are possible.
This has two inline drivers, which are handy.
The ratchet has 90 teeth, and even a knurled finger wheel.
Ergonomics are perfect, and the different configurations provide a variety of grips.
Top left: Anvanna and Pro BikeConstruction Quality
Construction feels fine. There are no visible imperfections with this set. Everything is chamfered, finished properly, nice and smooth.
Everything connects firmly with negligible wobble.Portability
The set is very compact, tucking in its case nicely. The whole set with case weighs only 99 grams, and the case even has a belt loop, so this will go unnoticed on a belt or even pocket.
The ratchet main unit is only 75mm long, so it can fit in Altoids tins, edc pouches, multi-tool sheath side-sleeves, etc.
Value
At $33 this is on the higher end of mini ratchet sets, though not by much.Conclusion
There are certainly ratchet sets that cost less and come with more, but they are not of this design. This is the first t-handle design ratchet so far.
It has been executed properly, with nice quality, 90 teeth, knurled wheel, and an extremely compact package. This offers many different configurations and grips, depending on required torque, reach, or comfort. Of course, it can be used as a right-angle ratchet. The inline driver that protrudes from the ratchet head may cause some issues with obstructions, compared to regular ratchets that do not have one, but even then, an inline driver can be used for those applications.For what it is and what it offers, this is an excellent option for edc. It has many useful features and the entire set comes in an extremely unobtrusive wallet that can be on a belt.
The main ratchet unit is nice and short, so this can be assembled or disassembled accordingly, to fit in specific pouches, tins, wallets, etc.
And the bits come in a bit holder, so even if you opt to ditch the wallet, the bits can still go in a pouch in their dedicated holder, instead of having them be loose.
Naturally, this design comes with its own pros and cons, and it will be up to you as to which outweigh which. If you want a regular right-angle ratchet, this is not one of those. If you need a t-handle ratchet, this will do nicely.
Recommended.
Pros
-T-handle design provides additional torque.
-Extremely compact kit.
-Many useful features for edc (knurled wheel, 90 teeth, inline drivers, belt loop, etc).
-Many different configurations possible.Cons
-Second inline driver protrudes from ratchet head, more prone to obstructions.If you liked this ratchet, also check out:
-
This guy gets it!

Awesome video, he shows lots of mini ratchets with their features.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login



















































