"bits" of a larger project....
-
@MultiMat said:
How do you know if you have ruined the metals temper
Can you re-temper metal if you have over heated it

I am about to do a bit of 'grinding' myself :D
tempering toughens metal, so im guessing he s going to ruin that by heating it too much (annealing?) and make the metal hard and brittle if he isnt careful
correct me if im wrong ive only been studying this briefly
-
I think you are more or less right
By heating and letting it cool it 'softens' the metal (as you say annealing) you need to re-temper it by heating and quenching (you have to get this temperature correct)
but I am open to suggestions
-
Tempering is basically un-doing a tiny part of the heat treatment -- you're making it a little bit softer and less brittle.
Annealing is like tempering taken all the way -- it completely removes all of the heat treatment, making it a lot softer and less brittle.
-
So how hot can you subject a hardened bit of metal before it looses its temper

Is there an easy way of re treating the metal to regain its hardening if you have over heated it

When grinding/drilling hardened metal is water good enough as a coolant

Sorry for hijacking your excellent thread Evil but I have finally found a place I can buy some Carbide drill bits.
I have some old SAK blades that I am keen to reinvent >:D >:D :D :D -
what are you thinking of working on matt ?
-
I am hopping to pop a SAK saw into my LM Pulse & also hopping to modify some old SAK blades & make some crazy Micras :D.
Unfortunately 4mm & 5mm carbide drill bits cost $40us each in Oz & are special order items :( :(.
There was a trade speSmurfpillst, from Sutton drill bits, at the proper tool shop I went to & he suggested I use carbide tipped masonry drill bits 'just round the bits wings off a bit' ???. The masonry bits only cost $5 so I will try to mod them :ahhh , the speSmurfpillst said he used to do it all the time(he used to be a tool maker though :D :D). Not sure if my Dremal will be able to grind the bits wings
. -
The fella did not say anything about a pack of bits :(.
I found a 'Formula Cobalt' drill bit that MIGHT work , it is a high speed drill bit though
, I will see how it goes before grinding the masonry bit
.I wonder why you can only seem to get carbide drills bits ,on the net , in very small sizes

-
@MultiMat said:
How do you know if you have ruined the metals temper
Can you re-temper metal if you have over heated it

I am about to do a bit of 'grinding' myself :D
In regard to temper, etc... what they have all been saying is pretty spot on. My advice is to avoid ruining the temper to begin with at all costs, if possible. Even if it means taking five times as long to get the job done. To me, the time and effort spent to re-temper such small accessories for a multitool just wouldn't be worth it. I would just start from scratch and make another. However, if it were a blade, that might be different....
@MultiMat said:
Sorry for hijacking your excellent thread Evil but I have finally found a place I can buy some Carbide drill bits.*no worries Mat, it keeps the thread alive lol. Stainless steel can be quite the beast. I have been getting by with Ridgid cobalt drill bits. Economical and do a decent job. I'd be crying if I broke a $40 drill bit lol. I use various diamond and carbide bits for misc drilling, machining, cutting and shaping.....
*@MultiMat said:
I found a 'Formula Cobalt' drill bit that MIGHT work , it is a high speed drill bit though*Just remember, you don't want to drill at too high a speed. Are you using just a regular dremel? While they have the speed, they lack torque. You'd want something slower with more torque. A drill press would be ideal to keep holes straight and true.....
Did you ever get your airbrush Mat?*
-
Evil is it obvious when you have over heated something & it has lost its temper , how do you tell

Yesterday I lopped part of a SAK saw's tang off , the offcut was very hot ::) I had a damp rag which I was putting on the SAK saw & used my Dremal to do it.Yep $40 is too much for me for 1 drill bit & a brittle one at that :ahhh :ahhh :D. I hope the cobalt I got works out they are a lot cheaper :D
I have a drill press I am dying to put through its paces :D :D. How fast should I run the Cobalt drill bit
& what cooling agent should I use
, guy at the shop mentioned kerosene

Airbrush ::) I have the funds squirreled away, know which one to get (thanks mate :D) & a rough plan.
Missing the courage ::) :D.Current plan involves me getting the Pulse & a couple of Micras under my belt , if I am happy with my work I will tart them up with a bit of pimping :D :D -
Lot s of things can be used as a coolant
In engineering workshops on lathes an stuff they use a white water based coolant
you can buy proper cutting grease/oil (I will go see If I can find some names, temaxol springs to mind)
I have used three in one oil, car engine oil and even WD40 in an emergency
When I use my bench grinder/belt sander I have a cup of water next to it and dunk the metal often
As said above its better to take your time and not bugger up the steel
-
Set your drill to the lowest speed it will run at. If its a cheap job like mine that means lifting its lid and changing the belt position. I use Ruko Universal Drill Paste... looks like used brown lard to me ;)
-
I used the stuff Neil uses years ago

I use this now (but I have run out) :-[
http://www.parkertools.co.uk/Product/0417211I have used this sort of thing in the past with a drill
http://www.toolbank.com/p/D5998/ROC53072So there are a lot of different makes and types out there I guess it doesn't matter so long as you use something and some must have made it down there to you Mat

Lard will also work! :ahhh
-
i used a tin of green stuff when i did workshop stuff works well it has a similar consistency to gel
-
@MultiMat said:
Evil is it obvious when you have over heated something & it has lost its temper , how do you tell
*Some signs are more obvious than others. Discoloration is often a tell-tale sign. If you are just going to constantly dip to keep the metal cool every so often, then water should suffice. If you are going to cool the metal as you are cutting there are many options as mentioned above. I always try to work cost-effectively. What I use is a mixture of water, oil and soap circulating through a cheap parts washer that I work over. The soap allows the oil to mix with the water... and for less than about 50 cents a gallon. Your mileage may vary.....
Like Neil said. If you have a drill press you will want to really crank down the speed. I have an old school drill press too where I have to lift the lid and change belt positions. I have even slowed mine down even more with an inline electronic speed control for when I work with other materials. While many will tell you that you need to let the tool do the work and this holds true the majority of the time, I have found that this is not always so when drilling through stainless. It takes considerable downward pressure in order to get the bit to bite and continually cut. You can have a new, sharp drill bit... without enough downward pressure you'll be there forever just spinning. Keep in mind these are just my opinions and things that have worked for me.....*
@MultiMat said:
Airbrush ::) I have the funds squirreled away, know which one to get (thanks mate :D) & a rough plan.
Missing the courage ::) :D.Current plan involves me getting the Pulse & a couple of Micras under my belt , if I am happy with my work I will tart them up with a bit of pimping :D :DDepending on which airbrush you end up with... if we ever do a sale or trade on here, I will throw in some accessories for you. I reprofile my own needles and fab my own crown tips, even custom handles for some of them.....
-
[i]This is a 1/4" socket driver bit that I made to fit into the bit card. I could of just ground the end of a standard 1/4" drive bit but the goal here was to have it fit into the bit card. If you ground the tip of a standard one flat, you would ruin the ball bearing/spring mechanism that holds a socket in place. I had found that some SOG's actually had something very similar to what I had in mind. I also found that it was a common complaint that the spring on it was prone to falling off fairly easy. After some trial and error, I came up with a stronger, thicker spring design that won't come off without using two implements to pry it off from both sides. I like it well enough that I just may make a permanent fold out version for my wave and my surge.....
~ evil ~
Close-up of spring mechanism.....

Here it is in the bit card.....

With a socket.....

-
@evil510 said:
[i]This is a 1/4" socket driver bit that I made to fit into the bit card. I could of just ground the end of a standard 1/4" drive bit but the goal here was to have it fit into the bit card. If you ground the tip of a standard one flat, you would ruin the ball bearing/spring mechanism that holds a socket in place. I had found that some SOG's actually had something very similar to what I had in mind. I also found that it was a common complaint that the spring on it was prone to falling off fairly easy. After some trial and error, I came up with a stronger, thicker spring design that won't come off without using two implements to pry it off from both sides. I like it well enough that I just may make a permanent fold out version for my wave and my surge.....~ evil ~
Close-up of spring mechanism.....

Here it is in the bit card.....

With a socket.....

That's awesome. You could make a killing selling those here.
-
Evil is it obvious when you have over heated something & it has lost its temper , how do you tell

*Some signs are more obvious than others. Discoloration is often a tell-tale sign. If you are just going to constantly dip to keep the metal cool every so often, then water should suffice. If you are going to cool the metal as you are cutting there are many options as mentioned above. I always try to work cost-effectively. What I use is a mixture of water, oil and soap circulating through a cheap parts washer that I work over. The soap allows the oil to mix with the water... and for less than about 50 cents a gallon. Your mileage may vary.....
Like Neil said. If you have a drill press you will want to really crank down the speed. I have an old school drill press too where I have to lift the lid and change belt positions. I have even slowed mine down even more with an inline electronic speed control for when I work with other materials. While many will tell you that you need to let the tool do the work and this holds true the majority of the time, I have found that this is not always so when drilling through stainless. It takes considerable downward pressure in order to get the bit to bite and continually cut. You can have a new, sharp drill bit... without enough downward pressure you'll be there forever just spinning. Keep in mind these are just my opinions and things that have worked for me.....*
@MultiMat said:
Airbrush ::) I have the funds squirreled away, know which one to get (thanks mate :D) & a rough plan.
Missing the courage ::) :D.Current plan involves me getting the Pulse & a couple of Micras under my belt , if I am happy with my work I will tart them up with a bit of pimping :D :DDepending on which airbrush you end up with... if we ever do a sale or trade on here, I will throw in some accessories for you. I reprofile my own needles and fab my own crown tips, even custom handles for some of them.....
Thanks for the tips , again :D
, Evil
.
I got a bottle of cutting/drilling lubricant that was not too dear. The drill bits I have got are Cobalt but described as 'High Speed drill bits'. Fast or slow on my Drill press (its a new made in China basic model press)
.I am fairly happy with the shaping I have done on my SAK saw into Pulse project , doing the locking groove is a real challenge. Trial & error have lead me to find the best Dremal cutting wheel (initially the wheel I was using was too thick).I am hopping on Sunday ,if I do not get called into work, I will drill the SAK saw & see how it fits :D :D.
Thanks for the trade offer Evil , I am still working up the courage to get the AirBrush ::) :D :D
BTW mate those modded bits look tops. Your mods are mighty impressive mate

-
@evil510 said:
[i]This is a 1/4" socket driver bit that I made to fit into the bit card. I could of just ground the end of a standard 1/4" drive bit but the goal here was to have it fit into the bit card. If you ground the tip of a standard one flat, you would ruin the ball bearing/spring mechanism that holds a socket in place. I had found that some SOG's actually had something very similar to what I had in mind. I also found that it was a common complaint that the spring on it was prone to falling off fairly easy. After some trial and error, I came up with a stronger, thicker spring design that won't come off without using two implements to pry it off from both sides. I like it well enough that I just may make a permanent fold out version for my wave and my surge.....Now that is a mod I could use!
Excellent work Evil

-
[i]This is a 1/4" socket driver bit that I made to fit into the bit card. I could of just ground the end of a standard 1/4" drive bit but the goal here was to have it fit into the bit card. If you ground the tip of a standard one flat, you would ruin the ball bearing/spring mechanism that holds a socket in place. I had found that some SOG's actually had something very similar to what I had in mind. I also found that it was a common complaint that the spring on it was prone to falling off fairly easy. After some trial and error, I came up with a stronger, thicker spring design that won't come off without using two implements to pry it off from both sides. I like it well enough that I just may make a permanent fold out version for my wave and my surge.....
Now that is a mod I could use!
Excellent work Evil

+1

Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login